Войти:
Оценок - 3, средний балл: 4.7 ( )

Инструкция по эксплуатации GE Monogram, модель RN328

Производитель: GE Monogram
Размер: 320.65 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


B.Outside top exhaust (Vertical duct–7. Round) • Since the hood is to be recirculated (not to be vented • Use the diagram or the hood as a template and outside), do not cut out any vent openings in the wall mark the locations on the cabinet for ductwork, or cabinet bottom. electrical wiring and keyhole screw slots. Hood mounting screws (4) 12 CUT HOLES 133.4. (30. hood) 133.4. (30. hood) Cut holes at marked locations for duct and electrical 163.4. (36. hood) 163.4. (36. hood) Cabinet front wiring. For the vertical duct, cut out 3/4. extra toward the front of the cabinet so you can move the duct freely when installing the hood. It may also ease Cabinet 73.4. bottom installation by cutting the hole 101.2. instead of 10.. 8. DIA. 95.8. Access 11.4. HOLE hole for 7. 53.4. round duct 13.8. Electrical access Wood shims Center hole (in cabinet bottom) (recessed-bottom cabinets line only–shims must be a minimum of 3/8. thick and cut to fit the width of the inner recessed cabinet bottom) 13 RUN WIRES Run the electrical wires through the wall or cabinet according to National Electrical Code and applicable local codes. NOTE: DO NOT turn the power on until installation is complete. 12 Installation Instructions SCREW IN PARTWAY Drive a mounting screw (from the hardware packet) partway into each center of the narrow neck of the keyhole slots marked on the cabinet bottom. OPTIONAL POWER CORD KIT JXHC1 An optional Power Cord Connection Kit, model JXHC1, is available at extra cost from your GE supplier for installation using a standard 3-prong, grounded wall outlet. Follow the Installation Instructions packed with the kit to connect the power cord to the range hood. 14 15 NOTE: If using optional Power Cord Kit JXHC1, feed the power cord through the hole in the top cabinet while raising the hood. Loop any excess length of cord and tie away with a suitable tape or tie. Cabinet 73.4. 3-prong wall outlet (if using cord connection)11.4. 13.4. dia. clearance hole for optional power supply location CL FEED IN WIRES Lift the hood into position and feed the house wiring through the wiring knockout. 16 SECURE HOOD Slide the hood back against the wall. Tighten the mounting screws. Be sure the screw heads are in the narrow neck of the keyhole slot. Keyhole (4) Mounting screw (4) NOTE: DO NOT PUSH ON FAN BLADE. Pushing on the blade may cause it to interfere with other hood parts. 17 CONNECT DUCTWORK TO HOOD (Ducted installations only) On 7. round installations, attach the 7. duct with sheet metal screws through the holes in the alignment ears. Use duct tape to make joints secure and air tight. Duct tape 18 Attachment ear tabs 7. round duct 13 Installation Instructions 19 INSTALL LIGHT BULB 23 REPLACE FILTER NOTE: A light bulb is not shipped with the hood. Make sure fan blade turns freely and replace the Obtain one locally. Purchase and install an ordinary filter. NOTE: On model JV347, install the metal screw-base light bulb, not more than 60 watts. grease filter if ducted or the charcoal filter if recirculated. 20 FOLLOW ELECTRICAL CODE Complete the electrical wiring according to National Electrical Code and local codes. NOTE: This hood must be permanently grounded. Connect house wiring (120 VAC) to hood wiring. 21 CONNECT WIRING Connect house black to hood black wire, house white to hood white wire and house ground under green ground screw. Securely tighten the strain relief clamp onto the house wiring. Green ground screw WARNING: IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THESE COPPER LEADS CAN RESULT IN A SERIOUS PROBLEM. USE ONLY CONNECTORS DESIGNED FOR JOINING COPPER TO ALUMINUM AND FOLLOW THE MANUFACTURER’S RECOMMENDED PROCEDURE CLOSELY. 22 REPLACE WIRING COVER Metal grease filter or charcoal filter The installation is complete. Turn on power at service panel, and test for proper operation. TROUBLESHOOTING CHECKLIST If the hood seems to be operating at high speed when the control is not set on high, or if ventilation seems inadequate, check the following: . Knockouts not removed from hood. . Damper blade not opening. . Reduced airflow because the duct is too small or the duct length is too long. . The duct is blocked. . Undersized or restrictive wall or roof cap. If the hood seems to make excessive noise: . Fan may be hitting the filter. Turn off the fan and remove the filter. Bend the filter down slightly in the center (into a dome shape) to allow fan clearance. Reinstall and adjust as needed. The fan does not work but the lights do: . Switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. . Check the wiring connections. See the CONNECT WIRING section in these Installation Instructions. Wiring cover 14 GE Range Hood Warranty. All warranty service provided by our Factory Service Centers, or an authorized Customer Ca...

Эта инструкция также подходит к моделям:
Вентиляторы - JV347 (320.65 kb)
Вентиляторы - JN327 (320.65 kb)
Вентиляторы - JV367 (320.65 kb)
Вентиляторы - JV338 (320.65 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории