Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
sections) Model HLB6 (600 cfm) in-line blower (includes two 4 .” x 18 .” to 10’’ round transitions) or HLB11 (1100 cfm) in-line blower (includes two 8” x 12” to 10’’ round transitions) OPTIONAL SOFFIT CHIMNEY RMN SERIES RMP SERIES BACKSPLASH 332KR in-line and exterior blower rough-in kit - Purchase separately. NP60000 SERIES HOOD (Canopy with blower controls & lighting. required for all installations.) OPTIONAL BAFFLE FILTERS RBF SERIES (Stainless steel wall covering with warming shelves. Optional.) HL0076 - 5 1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this hood. The NuTone Premier 60000 Series must be installed with blower models RM325H, RM326H, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. (Blowers sold separately). NOTE: In addition to the blower models listed above, this hood is also compatible with older internal versions 325H and 326H. However, discard the installation instructions included with those blowers and contact our technical support to obtain replacement instruction. Plan where and how the ductwork will be installed. If installing in-line blower, refer to instructions packed with in-line blower and follow steps 1 up to 6, 9, 10, 11, 13 and up of this manual. Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use 2” duct tape to seal duct joints. 7" (178 mm) ROUND DUCT ROOF CAP 7" (178 mm) ROUND ELBOW 24" TO 30" (609 to 762 mm) ABOVE COOKING SURFACE WALL CAP HOOD DECORATIVE FLUE or SOFFIT 12" (305 mm) HH0024A MODEL RM325H SINGLE BLOWER TYPICAL DUCTWORK 10" (254 mm) ROUND DUCT ROOF CAP WALL CAP HOOD DECORATIVE FLUE or SOFFIT 4-1/2" x 18-1/2" to 10" (114 x 470 to 254 mm) ROUND TRANSITION (see page 4) HH0025A 12" (305 mm) 24" TO 30" (609 to 762 mm) ABOVE COOKING SURFACE MODEL RM326H DUAL BLOWER TYPICAL DUCTWORK EXTERIOR BLOWER EXTERIOR BLOWER HOOD DECORATIVE FLUE or SOFFIT HH0026A 12" (305 mm) 24" TO 30" (609 to 762 mm) ABOVE COOKING SURFACE 332KR ROUGH-IN KIT (see page 5) 10" (254 mm) ROUND DUCT 10" (254 mm) ROUND ELBOW MODEL 331H, 332H, 335 OR 336 EXTERIOR BLOWER TYPICAL DUCTWORK 24” minimum above cookingsurface MODEL HLB3, HLB6, HLB9 OR HLB11 IN-LINE BLOWER TYPICAL DUCTWORK - 6 2. MEASURE INSTALLATION Dimensions for the most common installation are shown below. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is highly recommended for best capture of cooking impurities. Distances over 30” are at the installer and users discretion. Standard 18" (457 mm) H over-cooktop cabinet Hood 8 ft. (2.44 m) ceiling 18" (457 mm) 19" (483 mm) Top of wood mounting strip Standard RMP Series Backsplash (optional) 24" (610 mm) Standard 36" Cooktop (914 mm) H cooktop HH0028A INSTALLATION WITH STANDARD 18’’ INSTALLATION WITH STANDARD HIGH OVER-COOKTOP CABINET 12’’ SOFFIT OR OPTIONAL SOFFIT CHIMNEY RMN SERIES 3. PREPARE THE INSTALLATION Remove the installation kit from inside the hood. Make sure that the following items are included: - Wood strip - Installation manual - Accessories including: • Filters (Quantity varies depending on range hood width) • Bag of parts including: (4) flat head screws #10-2’’, (8) screws #8 x 3.4’’, (4) nuts #10-32, (2) wall anchors, (2) washers 3.16’’ ID x 3.4’’ OD Parts sold separately: - Interior blower Model RM325H or RM326H (both include rough-in kit) - In-line blower assembly HLB3, HLB6, HLB9 or HLB11 (all include transition) - In-line and exterior blower rough-in plate model 332KR, required for all In-line or Exterior Blowers - Exterior blower assembly 331H, 332H, 335 or 336 - Halogen lights (120 V, 50 W, PAR 20) - Heat lamps (Infrared, 120 V, BR40, 250 W max.) - RMP Series Backsplash (optional) - RBF Series Baffle filters (optional) - Transitions, duct, elbows, dampers, wall and roof caps. Refer to pages 4 and 5 for a complete list of venting options and model numbers. Using a Phillips #2 or a Robertson #2 screwdriver, unscrew the hood from the bottom of crate. Refer to figure beside to locate all 4 screws. Discard these screws and remove hood from wood pallet. HR0002 - 7 1234 4. INSTALL BACKSPLASH (OPTIONAL) (Optional) RMP Series Backsplash must be installed before the hood shell because the hood shell covers the backsplash top mounting screws. In order to be able to install the backsplash, make sure you have at least 18’’ clearance between bottom of hood and range control panel or cooktop. (See instructions packed with backsplash.) 5. INSTALL WOOD MOUNTING STRIP Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustration below and under step 2). Use #10 - 2’’ flat head screws to secure the mounting strip to the drywall. Make sure to hit the wall studs. (see page 7) CAUTION Due to the weight of this hood, ensure that the wood strip is attached to all of the available studs (2 studs minimum for a 30’’ hood, more as ...