Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
4. Install a roof or wall cap. Connect 8" round metal ductwork to cap and work back towards hood location. Use duct tape to seal the joints between ductwork sections. ROOF CAP 8” ROUND ELBOW 24” TO 30” ABOVE COOKING SURFACE 8” ROUND DUCT DECORATIVE FLUE HOOD INSTALL SUPPORT SYSTEM DRYWALL CROSS FRAMING 1. At hood location, install 2 X 4 cross framing between ceiling joists using dimensions shown. 2. Finish the ceiling surface. Be sure to mark the location of the ceiling joists and cross framing. 3. Position the support frame as shown. The UP ARROW should point towards the ceiling after installation. 4. Secure the upper half of support frame to joists and cross framing with four screws (6x70mm and four washers (D.6.4mm). Make sure screws are driven into center of joists and framing for maximum strength. 5. Adjust the overall height of the support frame. Loosen and re-tighten the 4 screws in the height adjustment slots as necessary. Insert 4 screws (3.9x9.5mm) and 4 washers (D.4.5mm) located in the Hardware Package. Note that #4 screws and #4 washers can be located on the front, and #4 screws and #4 washers can be located on the opposite face (rear). Note that the hood height is 10” and that: - on 8’ ceilings, the bottom of the hood must be 24” min. and 27” max. above the cooktop. - on 9’ ceilings, the bottom of the hood must be 27” min. and 30” max. above the cooktop. CEILING JOISTS FRONTHEIGHT ADJUSTMENT SLOTS SUPPORT FRAME 107/8” MOUNTING SCREWS (6x70mm) WASHERS (O6.4mm) TOP VIEW OF SUPPORT FRAME 107/8” 713/16” - 5 CONNECT DECORATIVE FLUE 1. Secure the upper flue to the upper support frame with the mounting screws. 2. Insert the lower flue moving it completely towards the top and fix it temporarily with retaining screws. INSERT THE LOWER FLUE2 RETAINING SCREWS (3.9x9.5mm) INSTALL DISCHARGE COLLAR Attach the discharge collar onto the hood; it must be attached by means of 4 mounting screws. Remove the tape located on the damper. LOWER FLUE UPPER FLUE MOUNTING SCREWS (3.9x9.5mm) 1 MOUNTING SCREWS (3.9x9.5mm) TAPE REMOVE THE - 6 MOUNT HOOD TO SUPPORT FRAME 1. Before mount hood to support frame removethe electrical box. 2. Mount hood to support frame. 3. Insert four (4) bolts through the top of thehood - from the inside. 4. Use four (4) nuts and four (4) washers (O6,4mm) to secure hood to support frame as shown. 5. Replace electrical box. USE (4) NUTS AND (4) WASHERS WASHER (D.6.4MM) BOLT NUT ELECTRICAL BOX WIRING Note: This range hood must be properly grounded. The unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. 1. Remove the wiring box cover. Remove a knockout from the wiring box. 2. Secure the conduit to the wiring box through a conduit connector. 3. Make electrical connections. Connect white to white, black to black and green to green. 4. Replace wiring box cover and screws. Make sure that wires are not pinched between cover and box. WIRING BOX COVER - 7 CONNECT DUCTWORK 1. Use 8" round metal duct to connect the duct collar on the hood to the ductwork above. 2. Use duct tape to make all joints secure and air tight. 3. Slide the lower decorative flue section downward, until it fits properly around hood. 4. Secure decorative flue to hood with mounting screws provided (3.9X9.5mm). MAINTENANCE Grease Filters The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. Remove filters by pushing filters towards the back of hood and rotating filters downward. Hood Cleaning 8” ROUND METAL DUCT LOWER DECORATIVE FLUE SECTION MOUNTING SCREWS (3.9X9.5mm) GREASE FILTERS Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: • Hot water with soap or detergent is all that is usually needed. • Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. • For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth. • For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleaser and water. Rub lightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface. • DO NOT allow deposits to remain for long periods of time. • DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. • DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only. - 8 OPERATION Controls The hood is operated using the slide controls under the front edge of the hood. The light switch t...