Оценок - , средний балл:
(
)
)
Производитель: NuTone
Размер: 2.26 mb
Название файла: 626976D.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Disconnect light assembly wire harness (white connector). |7~| Remove Air Chute - held in place with one (1) screw. NOTE: Be careful not to discon nect any wires. a 8 I Remove Baffle from air chute Rotate baffle. Reinsert baffle into air chute (as shown) so that baffle tabs fit all the way into slots in air chute. An audible “click” will be heard when fully installed. This will close off the air flow through the non-ducted slots on top of hood. 10 | Re-install air chute, re-connect wire harness, and replace light panel. NOTE: Be careful not to trap wires between support fin and light panel. SUPPORT FIN NuTone ALLURE™ WS1 SERIES RANGE HOOD Page 4 PREPARE THE HOOD TOP RECTANGULAR DUCT KNOCKOUT (Remove for 31A” x 10” Vertical & for 7”Round Discharge) SEMI-CIRCULAR DUCT KNOCKOUT (Remove for 7"Round Discharge) REAR RECTANGULAR DUCT KNOCKOUT (Remove for 3U” x 10 Horizontal Discharge) Mil Remove appropriate Duct Knockout(s) from top or back of —1 hood. UP TO 1” SIDE-TO-SIDE ADJUSTMENT TAPE PIVOT TOP/BACK EDGE DAMPER/DUCT CONNECTOR (Vertical discharge position shown) 12 | 3%” x 10” Ducted Discharge Only: Attach Damper/Duct Connector over knockout opening. Make sure damper Pivot is nearest to Top/Back Edge of hood. Remove Tape from damper flap. 7” Round Ducted Discharge Only: Re-install 7” Round Duct Plate removed in Step #1 under “PREPARE THE HOOD” section. Install a 7” round damper (purchase separately). Damper flap must open freely in direction of air flow (away from range hood). CONNECT WIRING A WARNING: To reduce the risk of electric shock, make sure power is switched off at the service panel. Lock or tag service panel to prevent power from being switched on accidentally. _HOUSE WIRING (120 VAC) □ CARDBOARD (Use to protect cooktop) Connect House Wiring (120 VAC) to hood. Use a piece of Cardboard to protect the cooktop, if necessary. GREEN GROUND SCREW d) Connect house black to hood black wire, house white to hood white wire, and house ground under Green Ground Screw. Securely tighten cable clamp onto house wiring. Replace wiring cover. NOTE | To accomodate off-center ductwork, the Damper/Duct Connector can be installed up to 1-inch on either side of hood center or the 7” Round Duct Plate can be installed up to /” on either side of hood center. In extreme off-center installations, one end of the duct connector may need to be trimmed to clear the electrical cable clamp. NuTone ALLURE™ WS1 SERIES RANGE HOOD INSTALL HOOD Page 5 NON-DUCTED FILTERS KEYHOLE (4) MOUNTING SCREW (4) |l| Hang hood from (4) Mounting Screws (from parts bag). Slide hood towards wall until mounting screws are engaged in narrow end of (4) Keyholes. Tighten mounting screws securely. CAUTION | DO NOT PUSH ON FAN BLADE. Pushing on the blade may cause it to interfere with other hood parts. If hood is to be installed Non-Ducted: Purchase a set of (2) non-ducted filters from your local distributor or retailer and attach them to the aluminum mesh filters. OPERATION jj IF^E m low high fan (( !! )) 1 low high J/ light - Fan: The 3-position rocker switch (on the left) controls the fan. The left position is low speed, center position is off, and right position is high speed. An indicator light shows that the fan is on. Light: The 3-position rocker switch (on the right) controls the lights. The left position is low light intensity, center position is off, and right position is high light intensity. DUCT TAPE |2~| Connect ductwork to hood. Use Duct Tape to make joints secure and air tight. Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16, 40 W Maximum Incandescent Bulbs. Purchase bulbs separately. CAUTION: Bulbs may be hot! Refer to bulb packaging for further information. |4| Replace filters and make sure fan blade turns freely. Turn on power at service panel, and test for proper operation. CLEANING A PAR20, 50W MAX. HALOGEN BULB (2) - or -R16, 40W MAX. INCANDESCENT BULB (2) WARNING: To reduce the risk of electric shock, disconnect from power supply before cleaning. Aluminum mesh filters: Clean frequently using hot water and a mild detergent. Filters are dishwasher safe. Charcoal filters: Clean filter surfaces frequently with a damp cloth and a mild detergent. DO NOT immerse filters in water or put in dishwasher. The special “Clean Sense” feature indicates when the filter is to be replaced. The blue and yellow strips will blend to green when it is time to change the filter. The “Clean Sense” feature works best when facing toward the cooking surface. To clean hood: Remove filters. Use a damp cloth and a mild detergent to wipe all grease-laden surfaces. Use care when cleaning fan blade - it must not become bent or misaligned. DO NOT ALLOW WATER TO ENTER MOTOR. Make sure all surfaces are completely dry before re-installing filters and restoring power. Motor is permanently lubricated. Do not oil or disassemble motor. NuTone ALLURE™ WS1 SERIES RANGE HOOD Page 6 SERVICE ...