Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Tape all joints with duct tape. Fig. 7. 4.Assemble the recirculation plenum to the flexible duct. Fig. 7. 5.Drill three (3) 1/16” diameter equally spaced holes through the duct and duct connector of the recirculation plenum. Fig.7. 6.Secure duct to the plenum’s connector with (3) sheet metal screws (not included). Tape all joints with duct tape. Fig. 7. FIG. 7 PLENUM (3) SCREWS 5” ALUMINUM FLEX DUCT 5” 6” ADAPTER BLOWER COLLAR A PREPARE THE HOOD NON - DUCTED CONFIGURATION, cont’d. 7. Carefully place the lower decorative flue into the recessed area of the range hood top. Fig. 6 8. Carefully slide the upper decorative flue down inside the lower flue. Note: air vents must be up. Fig. 6 9. Secure the recirculation plenum to the upper flue with (4) flat head screws. Fig. 8 PLENUM FIG. 8 4 FLAT HEAD SCREWS UPPER FLUE - 8 INSTALL THE HOOD Note: at least two people will be required to mount the hood. 1. Raise the hood into its mounting position. 2. Plug the power cord into the electric wall receptacle. Tuck excess cord behind the flue. 3. Align the rectangular opening on the back of the hood with the wall-mounting bracket. Gently lower the hood until it securely engages the bracket. Fig. 9 FIG. 9 MOUNTING SCREWS (4.8x38mm) RECTANGULAR CUTOUT WALL FRAMING MOUNTING BRACKET SCREWSSCREWS MOUNTING (4.8x38mm)(3.9x9.5mm) LEVEL 4. Level the hood with (2) screws (3.9x9.5mm) and secure with (4) mounting screws (4.8x38mm). Use drywall anchors provided if wall studs or framing are not available. Fig. 9 5. Secure the electrical system plate to the range hood with (2) mounting screws (3.9x9.5mm). Fig. 10 6. Raise the upper flue until its holes align with holes in the flue mounting bracket (located on ceiling). Fig. 11 7. Secure the flue with (2) mounting screws (3.9x9.5mm). Fig. 11 3.9x9.5mm MOUNTING SCREWS FIG.11 3.9x9.5mm SCREWS ELECTRICAL SYSTEM PLATE FIG.10 - 9 NON-DUCTED RECIRCULATION FILTER INSTALLATION 1. Purchase a charcoal filter (B03300488) from your dealer. 2. Install the filter by pressing the 2 tabs on the filter down into the special housing and rotating upward. MAINTENANCE Proper maintenance of the Range Hood will assure proper performance of the unit. Grease Filters The grease filters should be cleaned frequently. Use a warm detergent solution. Grease filters are dishwasher safe. CHARCOAL FILTER GREASE FILTERS TABS CLAMP Remove filter by pushing filter towards the back of hood and rotating filter downward. Charcoal Filter The charcoal filter should be changed every 6 months. To remove the filter press inward on the clamp and rotate the filter downward until the 2 tabs can be removed from the housing. Hood Cleaning Stainless steel is one of the easiest materials to keep clean. Occasional care will help preserve its fine appearance. Cleaning tips: • Hot water with soap or detergent is all that is usually needed. • Follow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth to avoid water marks. • For discolorations or deposits that persist, use a non-scratching household cleanser or stainless steel polishing powder with a little water and a soft cloth. • For stubborn cases, use a plastic scouring pad or soft bristle brush together with cleanser and water. Rub lightly in direction of polishing lines or "grain" of the stainless finish. Avoid using too much pressure which may mar the surface. • DO NOT allow deposits to remain for long periods of time. • DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface causing rust. • DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals which may be harmful. Rinse with water after exposure and wipe dry with a clean cloth. Painted surfaces should be cleaned with warm water and mild detergent only. - 10 OPERATION LIGHT SWITCH BLOWER Controls The hood is operated using the slide controls under the bottom of the hood. The light switch turns the lamps on and off. The blower switch :makes it possible to select the motor operating speed. Position 0: motor off. The pilot lamp lights up whenever the blower is on. HEAT SENTRY™ Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. 1) If blower is OFF - it turns blower ON to HIGH speed. 2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting. WARNING The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. When this occurs, it is impossible to turn the blower OFF with its switch. If you must stop the blower, do it from the main electrical panel. PILOT LAMP SWITCH HALOGEN BULBS This range hood requires two halogen bulbs (Type JC, 12Volt, 20 Watt Max, G-4 Base). ALWAYS SWITCH OFF THE ELECTRICITY SU...
Эта инструкция также подходит к моделям:Вентиляторы - NP51000 (939.8 kb)