|
Фрагмент инструкции
1000mm MIN. 380 - 415V 3PN + E H I C G 1L1 3L2 5L3 13NO A1 2T1 4T2 6T3 14NO A2 2T1 4T2 6T3 14NO A2 1L1 3L2 5L3 13NO A1 A B E D M TM F T Dimplex Industrial Fan Heater Models : CFP60, CFP90 & CFP120 THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Electrical IMPORTANT SAFETY ADVICE DO NOT COVER OR OBSTRUCT the air inlet or outlet grille. IMPORTANT – Disconnect from the mains supply before carrying out maintenance work. THIS HEATER MUST BE EARTHED Keep combustible materials such as drapes and other furnishings clear from the front, sides and rear of the heater. The heater should always be used upright on a flat, stable surface. DO NOT use this heater in the immediate surrounding of a bath, a shower or a swimming pool. DO NOT use this heater in areas where excessive dust exists. DO NOT store or use any flammable materials or sprays in the vicinity of the heater – FIRE HAZARD. DO NOT insert any foreign objects into the heaters openings. Risk of injury, electric shock or damage to the heater may occur. DO NOT use the heater on deep pile carpets or the long hair type of rugs. DO NOT operate the heater with wet hands. DO NOT use heater to dry your laundry. DO NOT operate the heater with the mains lead overhanging the front outlet grille. This heater is not intended for use by children or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the heater. The heater carries the Warning symbol indicating that it must not be covered. The socket-outlet must be accessible at all times to enable the mains plug to be disconnected as quickly as possible. The instruction leaflet belongs to the heater and must be kept in a safe place. If changing owners, the leaflet must be surrendered to the new owner. IMPORTANT – If the mains lead of this heater is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. Ensure proper manual handling procedures are observed at all times. CAUTION – In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this heater MUST NOT be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility. General The industrial fan heater is a robust, durable portable heater designed to coordinate with the Dimplex range of Air Curtains, providing environmental heating in commercial and light industrial environments. A heat selector switch and thermostat gives a wide range of control. Some of the heater’s features are highlighted in Fig. 2. (a) Thermostat / Heat control housing. (b) Robust tubular frame for carrying the heater. (c) Metal air outlet grille. (d) 2m long supply cable. (e) Impact resistant end mouldings. Model Heat Electrical Electrical Required Supply Weight Output Supply Load Plug Cable kW (per phase) Amps Amps 5G x kg CFP60 3 / 6 380-415V ~3PN 9.0 16 1.5mm. 15.0 220-240V ~3P * 15.6 16 CFP90 6 / 9 380-415V ~3PN 13.3 16 2.5mm. 16.0 220-240V ~3P * 23.0 32 CFP120 6 / 12 380-415V ~3PN 17.5 32 4.0mm. 16.0 220-240V ~3P * 30.4 32 The 5 Pin Plug supplied with this heater suits 380-415V ~3PN Star electrical supply. If 220-240V ~3P Delta supply is to be used a 4 Pin Plug is required (as denoted by * above). The Supply Cable is specifically chosen for each CFP heater and should only be replaced by a similar cable supplied by the manufacturer. See Fig. 4 for CFP Wiring Diagram. (References are listed below) A -Heat 1 Contactor B -Heat 2 Contactor C -Thermal Safety Cut-out Circuit D -Star / Delta Connector Blocks E -Heating Elemen...
Эта инструкция также подходит к моделям:Вентиляторы - CFP120 (1.02 mb)
Вентиляторы - CFP90 (1.02 mb)