Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
General Unpack the heater carefully and retain the packaging for possible future use, in the event of moving or returning the fire to your supplier. Loose coals are packed separately within the carton. When the heater is assembled the coals are placed on top off the fuel bed. The heaters is designed for use inset into a 407mm (16”) or 457mm (18”) wide by 559mm (22”) high fireplace opening see also section “Installation in a fire place opening”. A 2kw fan heater discreetly positioned in the canopy of the fire provides heating in cold weather. Switching allows half or full heat. A minimum distance of 1 metre (39”) must be maintained between the front of the heater and any surrounding furniture, overhanging curtains or other obstructions. Before connecting the heater check that the supply voltage is the same as that stated on the heater. Electrical Warning: This appliance must be earthed This heater must be used on an . (AC) supply only and the voltage marked on the heater must correspond with the supply voltage. For your convenience, the heater is fitted with a rewireable plug incorporating a 13 amp fuse. In the event of replacing the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362 must be used. Important Safety Advice When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: • If the appliance is damaged, check immediately with the supplier before installation and operation. • DO NOT use outdoors. • DO NOT use in the immediate surroundings of a bath shower or swimming pool. • DO NOT locate the heater immediately below a fixed socket outlet or connection box. • DO NOT COVER THE HEATER. Do not place material or garments on the heater, or obstruct the air circulation around the heater, for instance by curtains or furniture, as this could cause overheating and a fire risk. DO NOT leave young children, the elderly, or the infirm unsupervised in the vicinity of the heater. DO NOT use this heater in series with thermal control, a programmable controller, a timer or any other device that switches the heater automatically, since a fire risk exists when the heater is accidentally covered or displaced. Ensure that furniture, curtains or other combustible material are positioned NO closer than 1meter from the heater. In the event of a fault unplug the heater. Unplug the heater when not required for long periods. • Keep supply cord away from the front of the heater. • Although this heater complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs. • The appliance must be positioned so that the plug is accessible. • If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard. Text Box: Installation and Operating Instructions Longbourn Model No. LBN20 Incorporating 2Kw fan heater Issue 2 4/2/05 Installation in a Fireplace Opening At the rear of the fire, two adjustable supports are provided for leveling the fire where the base of the fireplace opening is raised above the level of the hearth. Adjust by removing the two screws holding each bracket in position, then refit the bracket and the two screws in the required position. Operation The unique flame effect may be enjoyed whether or not the heating elements are in operation. 'Please note: Used in an environment where background noise is very low, it may be possible to hear the fan which operates the flame effect. This is normal and should not be a cause for concern'. Controls The heater controls are located on the right hand side beneath the hinged canopy cover. Raise the canopy cover to access the controls. Three switches provide a choice of heat settings and an adjustable thermostat enables the room temperature to be controlled by adjusting the setting accordingly. A switch is in the ON position when the red indicator mark on the switch is visible. Switch 1 - Controls the electricity supply to the heater and the flame effect. Note: This switch must be in the ON position for the heater to operate. Switch 2 - Provides 1kw heat output, with thermostat control. Switch 3 – Provides 2kw heat output with switch 2, with thermostat control Setting the Thermostat Plug in and set all switches to ON. Turn the thermostat knob to MAX to warm the room rapidly. When the room temperature has reached the desired level, turn the thermostat knob back slowly until the thermostat just clicks off. The heater will then maintain the room temperature at the chosen level. NOTE – Should your heater fail to come on when the thermostat is at a low setting, this may be due to the room temperature being higher than the thermostat setting. Maintenance WARNING – BEFORE UNDERTAKING ANY MAINTENANCE OR CLEANING REMOVE PLUG OR DISCONNECT FROM THE ELECTRICITY SUPPLY. Lamp Replacement There are two lamps located beneath the fuel effect. To gain...