Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
. Service/Maintenance Space. Provide sufficient space to allow comfortable performance of service procedures and routine preventive maintenance. Consult installation instructions for specific details. CAUTION Replace all panels that are removed to perform service and maintenance procedures. Do not operate the machine with missing guards or with broken or missing parts. Do not bypass any safety devices. SW019 Input and Output Services . Water Pressure. Best performance will be realized if water is provided at a pressure of 30-85 psi (2.0-5.7 bar). Although the machine will function properly at lower pressure, increased fill times will occur. Water pressure higher than 100 psi (6.7 bar) may result in damage to machine plumbing. Component failure(s) and personal injury could result. . Steam Heat (Optional) Pressure. Best performance will be realized if steam is provided at a pressure of 30-80 psi (2.0-5.4 bar). Steam pressure higher than 125 psi (8.5 bar) may result in damage to steam components and may cause personal injury. For machines equipped with optional steam heat, install piping in accordance with approved commercial steam practices. Failure to install the supplied steam filter may void the warranty. . Drainage System. Provide drain lines or troughs large enough to accommodate the total number of gallons that could be dumped if all machines on the site drained at the same time from the highest attainable level. If troughs are used, they should be covered to support light foot traffic. . Power. For personal safety and for proper operation, the machine must be grounded in accordance with state and local codes. The ground connection must be to a proven earth ground, not to conduit or water pipes. Do not use fuses in place of the circuit breaker. An easy- access cutoff switch should also be provided. WARNING Ensure that a ground wire from a proven earth ground is connected to the ground lug near the input power block on this machine. Without proper grounding, personal injury from electric shock could occur and machine malfunctions may be evident. SW008 Always disconnect power and water supplies before a service technician performs any service procedure. Where applicable, steam and/or compressed air supplies should also be disconnected before service is performed. Misuse Never use this machine for any purpose other than washing fabric. . Never wash petroleum-soaked rags in the machine. This could result in an explosion. . Never wash machine parts or automotive parts in the machine. This could result in serious damage to the basket. . Never allow children to play on or around this machine. Death or serious injury can result if children become trapped in the machine. Do not leave children unattended while the machine door is open. These cautions apply to animals as well. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232085 Installation This manual is designed as a guide to the installation and maintenance of the UW35 and UW60 2 speed rigid-mount washer-extractor. All information, illustrations, and specifications contained in this manual are based on the latest product information available at the time of printing. We reserve the right to make changes at any time without notice. Machine Overview The design of the washer-extractor emphasizes performance reliability and long service life. The cylinder, shell, and main body panels are fabricated of stainless steel. The washer-extractor is mounted on a welded base frame which supports the bearings, cylinder, and shell. Electrical controls for the washer-extractor are housed in a separate enclosure located on the top of the machine. The controls are accessed by removing the top cover from the control module. One 2 speed motor drives the cylinder via a V-drive system. The cylinder is supported via the shaft by two bearings. The UW35 uses two ball bearing sets held in place by a cast-iron housing that is bolted to the A- frame. The UW60 uses two flange-mounted, spherical roller bearings bolted to the A-frame. On the UW60, a balance switch is installed between the faces of the A-frame to signal the controls to slow the machine when a severely out-of-balance load occurs during extract. The cylinder is constructed with lifters or ribs that lift the laundry from the bath solution when the cylinder rotates at slow speed and then allow the laundry to tumble back into the bath. This mechanical action accomplishes the washing function. The cylinder is perforated, allowing the water to drain from within during the wash and extract steps. The spray rinse feature (available only on S and P computers) consists of a fiber-reinforced clear hose connected to the center of the door glass and to both a hot and cold water inlet valve. A hemisphericallyshaped spray nozzle inside the door glass produces a fan-action water spray which disperses rinse water throughout the load. Water enters the machine through electromechanical water valves. Vacuum breakers are in...