Оценок - , средний балл: ( )

Инструкция по эксплуатации Delta Electronics, модель MCH 662

Производитель: Delta Electronics
Размер: 360.97 kb
Название файла: d1b5bb98-f6bc-7604-61ff-ce9acc9dc8a9.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

This appliance conforms to BS 800: 1988 and EEC Directive No. 78 308 regarding suppression of radio and television interference. 10 INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas. If it is necessary to fix the hood to a hollow construction plaster or partition board structure then it should be sufficiently reinforced to be quite rigid in the area of the cooker hood mounting brackets, and the appropriate rawl plugs used for this type of fixing (not supplied). Ducting The ducting must be fire retardant 100mm (4”ins) in diameter and the length should be no more than: 3 metres with one 90° bend 2 metres with two 90° bends Bends of more than 90° will reduce the efficiency of the hood and reduce the airflow. Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions. 11 Clearance Height A clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Unpacking The fittings supplied to install this cooker hood can be found with the instruction book inside the packaging. The fixing kit comprises: 2 - Wall fixing brackets 6 - Decor panel fixing screws 4 - Security fixing screws Fitting the Wall Brackets 1. Use the paper template provided to mark the hole positions on the wall for the bracket fixing screws. 2. Check the hole distances are correct with a tape measure as stated on the template. 3. At this stage it is important to allow 15mm (1/2 ins) clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing. Hob A: Built-in Electric Hob: 650mm clearance B: Built-in Gas hob: 700mm clearance C: Slot-in Electric Cooker: 685mm clearance D: Slot-in Gas Cooker: 787mm clearance 12 Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4 ins) minimum. The ducting used must be manufactured from fire retardant material. When the cooker hood is ducted externally the charcoal filter/s must be removed. To Fit the Ducting 1. Open the grille by pressing inwardly on the actuator bolts at each side of the grille, while pulling the grille panel downwards. The grille panel will slide into the intermediate position. Raise the lower edge of the grille forward through 45° angle until the grille becomes detached from the sl...