Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
3. Repeat for remaining filters. Complete Installation Check Range Hood Operation 1. Press the light button (F) to turn on the light, press again to turn light off. 2. Press the night light button (G) to turn off the night light, press again to turn night light off. 3. Press the On/Off button (A) to turn the fan on. The speed setting will appear in the display. 4. Press the “+” or “-” minus buttons to increase or decrease the fan speed. 5. Press the On/Off button (A) to turn off the fan. 6. If range hood does not operate, check to see whether a circuit breaker has tripped or a household fuse has blown. NOTE: To get the most efficient use from your new range hood, read the “Range Hood Use” section. RANGE HOOD USE The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen. Control Panel The range hood controls are located on the right-hand front surface of the range hood. A BCDE FG A. Fan motor on/off E. 10 minute timed boost B. Decrease fan motor speed F. Light C. Increase fan motor speed G. Night light D. Electronic Display Operating the Light 1. Press the light button (F) to turn on the light. 2. Press the light button (F) to turn off the light. Operating the Night Light 1. Press the night light button (G) to turn on the night light. 2. Press the night light button (G) to turn off the night light. Operating the Fan and Adjusting Fan Speed The fan has 4 speeds, 1 (low), 2 (medium), 3 (medium-high), and 4 (high). 1. Press the On/Off button (A) to turn the fan on. The speed setting will appear in the display. 2. Press the “plus” (+) or “minus” (-) buttons to increase or decrease the fan speed. 3. Press the On/Off button (A) to turn off the fan. 10-Minute Boost Function Press the “H” button to start the 10-minute boost function. The fan motor will run on its highest speed (4) as the display counts down from 10 minutes. At the end of 10 minutes, the fan will return to the previously selected speed. Reset Filter Alert After 100 hours of use, “C” will appear in the range hood display. This “C” indicates that the filter must be cleaned.”C” will only appear when turning off the range hood fan. Reset Alarm Display 1. Turn off the range hood fan and light. 2. Press the “H” button for 4 seconds. The “C” will disappear from the display and the counter will reset to “0.” Thermal Protector The range hood is equipped with a thermal protector to avoid overheating conditions. If the range hood shuts off while in use, press the on/off button to turn off the range hood. Wait approximately 60 minutes, then press the on/off button to restart the range hood. RANGE HOOD CARE Cleaning IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace grease filters before operating hood. Be sure lights are cool before cleaning the hood. Exterior Surfaces Clean the range hood with a mild detergent and soft cloth. Do not use abrasive cleanser or steel-wool pads. Metal Grease Filters The filters should be washed frequently. Place metal filters in dishwasher or hot detergent solution to clean. Drain water and let each filter dry thoroughly before replacing it. To Remove Metal Grease Filters 1. Turn off fan and lights. Check that halogen lamp is cool. 2. Pull out on knob and turn counterclockwise to release metal grease filters. To Replace Metal Grease Filters 1. Insert back edge of filter into rear channel of the filter opening. 2. Pull out on knob and turn counterclockwise, position front edge into place and release knob. Charcoal Filters - For Non-Vented (recirculating) Installations The charcoal filter is not washable nor reusable. It should be changed every 4 months in normal use or more frequently in heavy use. The charcoal filter captures unpleasant cooking odors. To Install Charcoal Filter 1. Turn fan and lights off. Check that halogen lamp is cool. 2. Remove the metal grease filters. See “Metal Grease Filters” section. 3. Set metal grease filters aside. 4. Place charcoal filter into opening. Press back and up on fixing hooks to secure filter in place. 5. Replace metal grease filters. See “Metal Grease Filters” section. To Replace Charcoal Filter 1. Turn fan and lights off. Check that halogen lamp is cool. 2. Remove the metal grease filters. See “Metal Grease Filters” section. 3. Set metal grease filters aside. 4. Discard the used charcoal filter. 5. Place charcoal filter into opening. Press back and up on fixing hooks to secure filter in place. 6. Replace metal grease filters. See “Metal Grease Filters” section. Replacing a Halogen Lamp Turn off the range hood and allow the halogen lamp to cool. Replace using a tissue. If new lamps do not operate, make sure the lamps are inserted correctly before calling service. 1. Disconnect power. 2. Remove the 2 screws holding the lighting support. 3. Gently ...