Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
0-M91 - latest edition** and all local codes and ordinances. A U.L.- or C.S.A.-listed conduit connector must be provided at each end of the power supply cable (at the range hood and at the junction box). Copies of the standards listed may be obtained from: * National Fire Protection Association Batterymarch Park Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575 Installation steps Preparation Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed. Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent. 1. If possible, disconnect and move freestanding or slide-in range from cabinet opening to provide easier access to rear wall. Otherwise put a thick, protective covering over countertop, cooktop or range to protect from damage or dirt. Select a flat surface for assembling the unit. Cover that surface with a protective covering and place all canopy hood parts and hardware in it. 2. Determine and mark the centerline on the wall where the canopy hood will be installed. 3. Attach the lower bracket securely to the wall at the height shown. The dimension shown on page 3 is for mounting the canopy hood 24” (61 cm) above cooking surface. The lower bracket must be mounted with the flanges on the bottom of the bracket so that the canopy hood will hang from them. If a backsplash is to be used with this canopy hood, it MUST be installed before the canopy hood. Installation instructions for the backsplash are supplied with the backsplash kit. The height of the backsplash will determine the height of the bottom edge of the canopy hood. 4. Attach the middle and upper brackets securely to the wall. The upper bracket should be installed about 1/8” (3 mm) away from the ceiling. The middle bracket (bright metal) must be installed with ends touching the wall and the curves facing outward. Note: If the canopy hood is installed more than 24" (61 cm), the middle bracket must be installed at the bottom point of the upper chimney sleeve. It may be necessary to cut the upper chimney. Be careful not to damage or bend upper chimney when cutting. 5. Determine and make all necessary cuts in the wall for the vent system. Install the vent system before the canopy hood. See venting methods on page 4. 30" hood 29-15/16" (76 cm) 24" (61.0 cm) min. 7-3/4" 4-7/16" 36" hood 35-7/8" (89.9 cm) 48" hood 47-1/4" (120 cm) 1-1/4" (31.8 mm) dia. hole (11.3 cm) (19.7 cm) base cabinet or cooking surface 6. Determine the required height for the power supply cable and cut a 1-1/4" (3.2 cm) hole at this location. Run wire through hole according the National Electrical Code or CSA Standards and local codes and ordinances. There must be enough power supply cable from the fused disconnect (or circuit breaker) box to make the connection in the hood’s electrical box. Use caulking to seal all openings. Do Not turn on power until installation is completed. Install chimney sections Electrical connection WARNING 7. Press on handle in front of filters to release filters from range hood canopy. Remove filters and set aside. WARNING 8. Remove the terminal box cover from the canopy hood. Remove the power supply cable knockout using a flat-blade screwdriver. Attach conduit connector into power supply cable opening so that conduit connector clamping screws are inside of canopy hood. Excessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury. adjustment screw 12. If roof or wall cap does not have a damper, attach damper to exhaust opening on top of the canopy using two Phillips-head screws. Connect vent system to damper or hood and seal all connections with duct tape. Electrical Shock Hazard Disconnect power before making electrical connections. Connect ground wire to green ground screw in terminal box. Failure to do so can result in death or electrical shock. vent upper bracket upper chimney 13. Carefully fit the upper chimney rear flanges behind the upper and middle bracket. 11. Make electrical connection: . Connect the power supply cable to hood terminal box through the U.L.- or C.S.A.-listed conduit connector. . Connect the white wire of the power supply cable with the white lead in the hood using a twist-on connector; connect the black wire of the power supply cable with the black lead in the hood using a twist-on connector. . Connect the power supply green (green and yellow) ground wire under the green, ground screw. . Tighten conduit connector screws. . Replace the terminal box cover. middle bracket upper chimney vent lower chimney 14. Carefully fit the lower chimney rear flanges behind the upper chimney flanges on the middle bracket and behind the lower bracket. upper chimney screws lower chimney screws 15. When upper and lower chimney sections are in final position, attach the top of the upper chimney and the bottom ...
Эта инструкция также подходит к моделям:Вентиляторы - 48 (318.33 kb)
Вентиляторы - 36 (318.33 kb)