Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (not included). Age: 2-5 years Weight limit: 55 lbs (25 kg). sher-price.com Consumer Information #8 x 2." Screw - 1 *We’ve included one extra .354" cap nut for your convenience. WARNING TO AVOID SERIOUS INJURY: • Adult supervision is required. • Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools or other bodies of water. • Always wear shoes. • Never allow more than one rider. #8 x." Screw - 6 ALL SHOWN ACTUAL SIZE .354" Cap Nut - 2* .354" Parts • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry cloth before assembly. • Some parts shown are assembled to both sides of he trike. • Tighten assembled screws with a Phillips screwdriver. Do not over-tighten the screws. Note: Tighten and loosen the screws with a Phillips screwdriver. Do not over-tighten the screws. Seat 2 Fork Covers Front Wheel Assembly Fork Frame Handlebar Back Straight Axle 2 Bushings 2 Wheel Hubs 2 Wheel Caps 4 Pedal Hubs 2 Rear Wheels Part not shown: Label Sheet Handlebar Front 2 Assembly CAUTION This product contains small parts in its unassembled state. Adult assembly is required. Frame Seat PUSHWheel Hub (Flat Side Down) Bushing (Grooved Side Down) • Fit the seat onto the frame. Push firmly near the back end of the seat to "snap" it into place. Straight Axle Straight Axle Cap Nut Rear Wheel (Indented Side Down) 1 2 Straight Axle Assembly Bottom View 3 • Turn the frame upside down. • Insert the straight axle assembly through the holes in the rear of the frame. • Turn the assembly upright. • Slide a bushing, smooth side first, onto the end of the straight axle. • Slide a wheel, flat side fi rst, onto the end of the straight axle. • Slide a wheel hub, pointed end first, onto the end of the straight axle. Bushing (Smooth Side First) Wheel Hub (Pointed End First) Wheel (Flat Side First) Straight Axle 4 • Place one end of the straight axle into the cap nut. Tap the end of the straight axle with a hammer. Make sure the cap nut is securely attached to the straight axle. • Slide a wheel hub, flat side down, onto the straight axle. • Slide a rear wheel, indented side down, onto the straight axle. • Slide a bushing, grooved side down, onto the straight axle. 3 Assembly 5 • Fit the cap nut on the end of the straight axle. • Tap the cap nut with a hammer. Gently pull the rear wheel to be sure the cap nut is securely attached to the straight axle. Hint: You may need the help of another adult to hold the other end of the straight axle in place. Wheel Hub Wheel Cap 6 • Fit the tabs on the wheel cap into the slots in the wheel hub. Push to "snap" the wheel cap in place. • Repeat this procedure to attach the other wheel cap to the other wheel hub. Pedal Hub 7 Pedal Hub Pedal Axle Tab • Fit two pedal hubs onto the pedal axle tabs. Make sure the tabs fit into the slot in each pedal hub. • While holding the pedal hubs on the pedal axle, insert the pedal axle into the hole in the center of the front wheel. • Press the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel. • Repeat this procedure on the other side with the other two pedal hubs. Fork Arms Pedal Axle Groove Fork Cover Front Wheel Assembly 8 • Place the front wheel assembly between the fork arms. Make sure the pedal axle fits into the groove at the bottom of each fork arm. • Place a fork cover over the pedal axle on one fork arm. • Insert two #8 x ." screws into the fork cover and tighten. • Repeat this procedure to attach the other fork cover to the other fork arm. 4 Assembly Label Decoration Fork Post Fork Cover REAR OF TRIKE 9 • Insert the fork post up through the hole in the neck of the frame. Make sure the fork is positioned so that the fork covers face the rear wheels. Handlebar Front ." Screw ." Screw 2." Screw Handlebar Back 10 Fork Post 553Bac k F r ont • Wash your hands before applying the labels. • Make sure the areas where the labels will be applied are clean and dry. Wipe your vehicle with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying a label more than once. • Apply the labels as shown in the illustration above. • After applying a label, rub the label firmly with a cloth to make sure the label is adhered to your vehicle. • Fit the handlebar front to the fork post. Hint: The handlebar front is designed to assemble to the fork post one way. • Fit the handlebar back to the fork post and handlebar front. Hold them together firmly. • First, insert the remaining #8 x ." screws through the outer holes in the handlebar back and tighten. • Then, insert the #8 x 2." screw through the center hole in the handlebar back and tighten. 5 6 2 4 7 1 4 Label Decoration Right Side Consumer Information • Periodically, check the plastic parts and if broken or cracked...