Оценок - , средний балл:
(
)
)
Производитель: Trek
Размер: 551.2 kb
Название файла: 06_Incite_6i_8i.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
2. Wrap the wire around the front brake cable, diverting the determined amount. 3. Continue routing the wire, either by wrapping around the fork or frame tube, or attach the wire to the fork or frame tube with electrical tape. 4. As needed, solidify the wire attachment with either nylon ties or electrical tape. Installation Attaching the sensor The magnet must pass across the line on the sensor (Figure 9). To install the sensor 1. Align the sensor with the magnet. 2. Orient the sensor so that the clearance between the sensor and the magnet is between 1 to 3mm. The sensor can be rotated around the fork about 45 degrees. If needed, the sensor and magnet can be moved up or down the spoke and fork to change the amount of clearance. 3. Attach the sensor with nylon ties, but do Figure 9- Magnet alignment and clearance 1.0 - 3.0mm not fully tighten. 4. With the computer in the computer base, check the alignment of the sensor and magnet by spinning the wheel and noting if the computer is displaying speed. If the computer shows current speed, the sensor is reading the magnet. If the computer is not displaying a value, realign the sensor and magnet until one is displayed. Installation 5. Tighten the nylon ties and trim the excess length (Figure 10). Figure 0- Trim excess nylon tie Figure 0- Trim excess nylon tie length 0 Installation EASy SETuP (RESET) You can program the starting values of your computer in a single, easy procedure: • Units • Clock • Wheelsize • Odometer The Units setting tells the computer which conversion to use: metric or SAE (“English”): MH = miles KMH = kilometers You can set the clock for 12 or 24 hour display, which changes how time appears in the afternoon, such as 3PM: 12 hour clock 3:00 24 hour clock 15:00 You can set the wheel size by simply choosing from a menu listing tire sizes, or you can set custom values listed in a chart. For the most precision, do a “rollout” test. The rollout test is described on page 22. You can set the odometer to be at “0” or you can start at a different value. This allows you to keep track of your previous mileage after the computer has Reset (started over at 0), such as after installing a new battery. Easy setup (ReSet) using the buttons CLKTMEAVGMAXTRPODOMHFigure - Buttons on the Incite 6i computer Mode Set When setting the computer, there are three ways to use the buttons. To help you remember, notice the way each term is underlined. To help you remember, these terms will look the same throughout the manual. Push- touch once Cycle - push repeatedly as needed Hold- push and hold in for two or three seconds The buttons on the computer are (Figure 11): Set• button on the right side Mode button on the bottom To set the computer, you must Push, Cycle, or Hold the two buttons in a specific sequence. 2 Easy setup (ReSet) CLKTMEAVGMAXTRPODOMHMode Set Mode Set To set the computer 1. Cycle Mode to ODO (Figure 12). CLKTMEAVGMAXTRPODOMHFigure 2- ODO screen 2. HoldSet• KMH or MH flashes. 3. Cycle Mode MH and KMH interchange on the screen. 4. Push Set• to select. 5-digit odometer value appears with first digit flashing. 5. Cycle Mode to your preferred value. 6. Push Set• to select. The next digit flashes. 7. Repeat steps 5 and 6 until all digits are selected. The computer returns to the start screen. To set 6i wheel size For 8i, go to page 14, To set 8i wheel size 1. Cycle Mode to TME. 2. HoldSet• Wheel size appears on the screen. Easy setup (ReSet) 3 CLKTMEAVGMAXTRPODOMHSet Set Mode Note: If you want to set a custom wheel size, go to page 24 now. 3. Cycle Mode The Wheel Size changes. 4. Hold Set• to select. The computer returns to current speed. To set 8i wheel size The 8i allows you to use two different wheel sizes. The icon for Wheel 1 is a small circle. The icon for Wheel 2 is a partial circle surrounding the Wheel 1 icon (Figure 13). 1. Cycle Mode to TME. 2. HoldSet• Wheel Select icon appears on the screen. 3. Cycle Set• to show Wheel 1 or Wheel 2. 4. Push Mode to select. The wheel size appears. Note: If you want to set a custom wheel size, go to page 24 now. Figure 3- Select wheel screen 4 Easy setup (ReSet) CLKTMEAVGMAXTRPODOMHSet Set Mode 5. Cycle Mode The wheel size changes. 6. Hold Set• to select. The computer returns to current speed. To set the second wheel size, repeat the instructions, but select the other Wheel Select icon. To select the wheel for use 1. 2. Holdthe left Modeand the right Modetogether. Cycle Mode to TRP The Wheel Select icon changes (Figure 13). Repeat step 2 to change again. Easy setup (ReSet) 5 CLKTMEAVGMAXTRPODOMHSet Set Mode To set Clock 1. Cycle Mode to CLK (Figure 14). 2. HoldSet• “12” or “24” flashes. 3. Cycle Mode 12 and 24 interchange on the screen. 4. Push Set• to select The clock appears on the screen with the Hour flashing. 5. Cycle Mode The Hour changes. 6. Push Set• to select. The Minutes flash. 7. Cycle Mode 8. Push Set• to select. The computer returns to current speed. CLKFigure 4- CLOCK screen 6 Easy setup (ReSet) CLKTMEAVG...
Эта инструкция также подходит к моделям:Велосипеды - 8i (551.2 kb)