Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
Please read this manual carefully and save it for future reference. If you do not understand the information in this manual, or you have a question about your Incite 9i computer that this manual does not cover, consult your Trek dealer. If you have a question or problem that your Trek dealer can’t handle, contact us at: Trek Bicycle Corporation Attn: Customer Service 801 W. Madison Street Waterloo, Wisconsin 53594 trekbikes.com © Copyright Trek Bicycle Corporation (920) 478-4670 2006 All rights reserved CONTENTS Safety and general guidelines..................................................1 Functions ..................................................................................2 Installation................................................................................4 Placing the computer on the handlebar ..............................5 Placing the magnet..............................................................7 Attaching the computer wire...............................................8 Attaching the sensors ..........................................................9 Easy setup (ReSet)..................................................................11 ReStart- Getting ready to ride ...............................................17 Additional information...........................................................18 Troubleshooting .....................................................................19 Replacing the battery.............................................................20 Setting custom wheel size......................................................22 Limited Warranty....................................................................25 SAfETy ANd gENERAl guIdElINES While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the road, you could hit an obstacle, which may cause you to lose control and fall. Make sure the computer wire cannot contact the tire or wheel spokes (Figure 2). The wire could be damaged causing the computer to malfunction. Also, the wire could get caught, causing you to lose control and fall. Figure - Watch the road when riding. Figure 2- Keep the wire out of the spokes Safety and General guidelines fuNCTIONS Table - Function abbreviations, names, and explanations functionExplanationCloCK ClK TME Time of day Displays in hours and minutes, or stopwatch showing seconds. 2-hour with AM/PM or 24-hour format Highest reading: 23:59 (clock) or 23:59:59 (stopwatch) CLKoDoMETEr oDo Distance ridden Displays in miles or kilometers. TrP-Trip (since last restart) TTl- Total since last reset Highest reading: 99,999 CLKTMEAVGMAXTRPODOMHPACEr Always displays Indicates whether current speed is faster or slower than average speed Displayed by arrow pointing up (faster) or down (slower). CLKTMEAVGMAXTRPMH ODO Functions SPEED Always displays Current speed of the bicycle in miles per hour (MH) or kilometers per hour (KMH) AVG- Average speed since last restart, displayed to tenths. MAX- Highest value since last restart Highest readings: 80.5mph or 29.6kph CLK TME AVG MAX TRP MH WHEEl SElECTIon Always displays Indicates which wheel setting is in use by computer ODO CLK TME AVG MAX TRP ODO MH Temperature Current temperature displayed in Fahrenheit or Celsius in whole numbers, updated every 30 seconds. range: • -2 to 40°F +/-2° • - 9 to 60°C +/- ° CAD ( i only) Cadence number of revolutions per minute of the crankset displayed in whole number. Maximum 240 . Functions INSTAllATION Stem mount Handlebar mount Speed sensor Figure 3- location on bicycle of sensors and computer Cadence sensor Tools needed: • Electrical tape • Slot-type screwdriver • Phillips-type screwdriver • Scissors Installation Placing the computer on the handlebar The Trek Incite 9i or 11i computer can be mounted on the handlebar or on the stem (Figure 3). To install the computer on handlebar 1. Select the bar clamp that fits your bike. 31.8mm bars: large clamp 25.4mm and 26.0mm: small clamp 22.2mm bar: small clamp with rubber shim 2. Insert the handlebar clamp into the back of the computer base (Figure 4) and slide it towards the front of the base. 3. Insert the rubber friction pad into the computer base, aligned across the computer base. 4. With the wire pointing toward the front of the bike, wrap the bar clamp around the handlebar. 5. Insert the screw through the washer and into the computer base. 6. Tighten the screw until the computer base cannot rotate on the handlebar. 7. Slide the computer into the computer base until the front of the computer and computer base line up. Figure 4- Clamp and friction pad in computer base Installation Figure 5- Make sure the com- puter cannot be bounced off. Figure 6- nylon tie threaded through computer base Check that the computer base cannot be rotated around the handlebar, and that the computer cannot slide backwards on the computer base (Figure 5). To install the computer on the stem 1. Insert the rubber fricti...
Эта инструкция также подходит к моделям:Велосипеды - 9i (604.09 kb)