Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
Connect the PULSE EXTENSION WIRE(40) to the CONTROL WIRE(24). Insert the REAR FRAME(5) onto the FRONT FRAME(1) and secure with BUTTON HEAD BOLTS(M10x1.5x20mm)(66), BUTTON HEAD BOLTS(M10x1.5x53mm) (67), ARC WASHERS(M10)(87), LOCK WASHERS(M10)(89), WASHER(M10)(92), and ACORN NUT (M10x1.5)(85). NOTE: See page 13 for detailed leveling instructions to prevent rocking. ASSEMBLY INSTRUCTIONS 9 B. A. (Assembled at the factory) STEP 5 Refer to illustration A. Attach the HANDRAIL(8) to the SEAT FRAME(7) with CARRIAGE BOLTS (M8x1.25x45mm)(62), ARC WASHERS(M8)(86), LOCK WASHERS(M8)(88), and ACORN NUTS(M8x1.25) (84). STEP 6 Refer to illustration B. Slide the SEAT FRAME(7) onto the REAR FRAME(5) and lock in position with the ADJUSTMENT KNOB(51). Attach the STOPPERS(52) to the top end of the REAR FRAME(5) with HEX BOLT(M8x1.25x80mm)(68) and NUT(M8x1.25)(80). Also, please verify that the other STOPPERS(52) are assembled at the factory. NOTE: Be careful not to damage the PULSE SENSOR WIRES(44) when attaching the HANDRAIL(8) and the SEAT FRAME(7). ASSEMBLY INSTRUCTIONS 10 STEP 7 Refer to the inset drawing. Plug the PULSE COIL WIRE(42) into the SOCKET of the PULSE EXTENSION WIRE(40) located on the REAR FRAME(5). Clip the GROMMET PLUGS(43) onto both ends of the PULSE COIL WIRE(42). Connect both ends of the PULSE COIL WIRE(42) to the PULSE SENSOR WIRES(44). Push the plugs and excess wires back into the HANDRAIL(8) and secure with the GROMMET PLUGS(43). STEP 8 Attach the SEAT(48) to the SEAT FRAME(7) with ROUND HEAD BOLTS(M6x1x15mm)(73). Attach the BACK CUSHION(49) to the SEAT FRAME(7) with BUTTON HEAD BOLTS(M8x1.25x40mm)(64). Socket of Pulse Extension Wire(40) ASSEMBLY INSTRUCTIONS 11 STEP 9 NOTE: The RIGHT PEDAL(38) has R stamped on the end of the pedal shaft. The RIGHT PEDAL(38) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(36) has L stamped on the end of the pedal shaft. The LEFT PEDAL(36) has left hand threads and is tightened by turning counterclockwise. Thread the RIGHT PEDAL(38) into the RIGHT CRANK(33) as shown. Tighten the pedal securely. Select the RIGHT PEDAL STRAP(39) which has R marked on the bottom side of the strap. Snap the two hole end to the inside edge of the RIGHT PEDAL(38). Snap the other end to the outside edge of the RIGHT PEDAL(38) with the R mark on the bottom of the RIGHT PEDAL STRAP(39). Select adjustment holes which allow your foot to be easily removed from the pedals. Use the same procedure to attach the LEFT PEDAL(36) to the LEFT CRANK(32) and snap the LEFT PEDAL STRAP(37) to the LEFT PEDAL(36). STEP 10 Slide the UPRIGHT SLEEVE(29) over the UPRIGHT(3). Connect the CONNECTION WIRE(25) to the CONTROL WIRE(24). Insert the UPRIGHT(3) onto the FRONT FRAME(1) and secure with FLAT HEAD BOLTS(M8x1.25x15mm)(70). Slide the UPRIGHT SLEEVE(29) down to cover the bolt heads. ASSEMBLY INSTRUCTIONS 12 STEP 11 Refer to the inset drawing. Run the CONNECTION WIRE(25) through the hole in the plate on the HANDLEBAR(4). Attach the HANDLEBAR(4) to the UPRIGHT(3) with BUTTON HEAD BOLT (M8x1.25x40mm)(64) and FLAT HEAD SCREWS(M6x1x12mm)(69). STEP 12 Install four AA batteries into the COMPUTER(26). Four batteries are included. See page 17 for detailed battery installation instructions. Plug the CONNECTION WIRE(25) into the EXTENSION WIRE on the COMPUTER(26). Push the plugs and excess wires back into the UPRIGHT(3) and slide the COMPUTER(26) onto the plate on the HANDLEBAR(4). STEP 13 Attach the MOUNTING BRACKET(93) to the UPRIGHT(3) with ROUND HEAD SCREWS(M4x0.7x15mm) (75). Place the WATER BOTTLE(94) in the MOUNTING BRACKET(93). 13 SET UP INSTRUCTIONS Place the Magnetic Fusion 7100 Bike in the area where it will be used. It is recommended that the Magnetic Fusion 7100 Bike be placed on an equipment mat. The Magnetic Fusion 7100 Bike is approximately 53 1/4 inches long x 24 1/2 inches wide x 51 3/4 inches tall. (These dimensions may vary up to one inch.) An area 4 feet wide x 7 feet long is required for safe operation of the Magnetic Fusion 7100 Bike. Make sure that adequate space is available for access to and passage around the Magnetic Fusion 7100 Bike. To level the Magnetic Fusion 7100 Bike, first screw the STAND(60) located in the middle of the FRONT FRAME(1) all the way up into the FRONT FRAME(1) so that it is not touching the floor. Adjust the two LEVELING CAPS(57) on the REAR STABILIZER(6). When the LEVELING CAPS(57) are adjusted and the Magnetic Fusion 7100 Bike is stable, rotate the STAND(60) to make it contact with the floor. While you are adjusting the LEVELING CAPS(57) the STAND(60) must not be in contact with the floor. Only after the Magnetic Fusion 7100 Bike has been stabilized with the LEVELING CAPS(57) will you position the STAND(60) so it is in contact with the floor to provide extra stability for the frame. The Magnetic Fusion 7100 Bike has a WHEEL(54) on the FRONT STABILIZER (2). Lift up the REAR STABILIZER(6) to move the Magnetic Fusion 7100 Bike. LEVELING: MOVING: EQUIPMEN...
Эта инструкция также подходит к моделям:Велосипеды - Fusion 7100 (697.75 kb)