Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Please write down these numbers In the spaces provided above for future reference. QUESTIONS? DO NOT RETURN this product to the store where purchased. CALL OUR TOLL FREE HELPLINE USA: (888)340-0482 Canada: (800) 897-6025 CAUTION! Please read the precautions and instructions in this manual before using this equipmenL Please save this manual for future reference. OWNER S MANUAL KEYS FITNESS PRODUCTS, L.P. PO Box 551239 Dallas, Texas 75355-1239 MADE IN TAIWAN Before You Start Thank you for purchasing a Keys exercise bicycle! This quality product you have chosen was designed to meet your needs for cardiovascular exercise. • Before you start, please read the Owner's Manual and become familiar with the operation of your new exercise bicycle. • If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate. • If you have heart problems, you are not active, and/or are over the age of 50 years, do not use the pre-set exercise bicyde programs or start an exercise program without first contacting and getting approval from your physician. • To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. Keys recommends a sealed water bottle for beverages consumed while using the recumbent bicyde. Assembly Instructions STEP I Insert two M8 x 1.25 x 60 CARRIAGE BOLTS through “square holes” in REAR FOOT TUBE and through rear of FRAME as shown. b] Fasten with 5/16” WASHERS and M8 x 1.25 CAP NUTS. c] Tighten CAP NUTS. d] Push FOOT CAPS over ends of REAR M8 x 1.25 x 60 CARRIAGE BOLT FRAME 5/16" WASHER FOOT CAP ‘ FOOT CAP STEP 2 A[ Insert two M8 x 1.25 x 60 CARRIAGE BOLTS through “square holes” in FRONT FOOT TUBE and through front of FRAME as shown. Fasten with 5/16” WASHERS and M8 x 1.25 CAP NUTS. Tighten CAP NUTS. Slide WHEELS over ends of FRONT FOOT TUBE. 0 M8 x 1.25 CAP Assembly Instructions STEP3 Aj Thread SHAFTS of RIGHTHAND and LEFTHAND PEDALS into CRANK and tighten with wrench STEP 4 Place SEAT upside down and remove NUTS on MOUNTING BOLTS. b] Lower MOUNTING PLATE of SEAT POST down onto MOUNTING BOLTS and fasten with removed NUTS. 3 Tighten NUTS. STEPS a| Turn LOCKING KNOB counterclockwise to loosen. b] Pull LOCKING KNOB out and insert SEAT POST into SEAT POST TUBE to desired SEAT height. 3 Release LOCKING KNOB so that it springs into hole in SEAT POST and turn clockwise until tight to remove any looseness. IMPORTANT LOCKING KNOB must be locked tightly into hole is SEAT POST before you sit on the SEAT. STEP 6 !dj Plug EXTENSION WIRE into REED SWITCH WIRE. Wrap connection with tape provided on REED SWITCH WIRE. b] Insert EXTENSION WIRE and PICKUP WIRE through CONSOLE TUBE and insert CONSOLE TUBE into FRAME. Fasten with BUTTON HEAD SCREWS and FLAT WASHERS. NOTE: DO NOT pinch wires while attaching CONSOLE TUBE. EXTENSION WIRE Assembly Instructions STEP 7 Insert RIGHTHAND and LEFTHAND HANDLEBAR BRACKETS into CONSOLE TUBE. NOTE: Make sure TTJBES are angled inward at the front of bike as shown. Fasten HANDLEBAR BRACKETS to CONSOLE TUBE with BUTTON HEAD SCREWS and FLAT WASHERS. NOTE: DO NOT pinch wires between HANDLEBAR BRACKETS and CONSOLE TUBE. RIGHTHAND HANDLEBAR BRACKET TUBE BUTTON HEAD SCREW LEFTHAND HANDLEBAR BRACKET '"TUBE CONSOLE TUBE FLAT WASHER REAR SLEEVE REAR HANDLEBAR REAR S' ELBOW PAD REAR HANDLEBAR BALL PLUG FRONT SLEEVE B NOTE: Liquid soap applied to handlebars will help sleeves slide easier. Insert FRONT and REAR HANDLEBARS into RIGHTHAND and LEFTHAND HANDLEBAR BRACKETS. a d] Push BALL PLUGS into end of REAR fFA*TT>r CTO A VC LEFTHAND HANDLEBAR BRACKET FRONT HANDLEBAR ELBOW PAD RIGHTHAND HANDLEBAR BRACKET STEP 8 [a] Slide FRONT SLEEVE and REAR SLEEVES over FRONT and REAR HANDLEBARS. MACHINE SCREW MACHINE SCREW Attach ELBOW PADS and HANDLEBARS to HANDLEBAR BRACKETS with MACHINE SCREWS. Assembly Instructions STEP 9 NOTE: Batteries are not included. J Insert BATTERIES. CAUTION: DO NOT use rechargeable batteries. Using rechargeable batteries will cause a short circuit and destroy monitor (4) "D" SIZE STEP 10 a| Carefully plug EXTENSION WIRE and PICKUP WERE into bottom of CONSOLE. Bl Fasten CONSOLE to HANDLEBAR —1 BRACKETS with MACHINE SCREWS. EXTENSION « WIRE CONSOLE PICKUP WIRE HANDLEBAR BRACKET MACHINE SCREW Console Functions Your bike is equipped with programmable monitor to help you track your progress and motivate you to reach your fitness goals. This monitor provides different programs designed to tailor to your fitness goals. Simply choose the program you like, set tfx time limit and begin exerasing-your monitor wifi then show your pulse, approximate calories burned, elapsed time, speed anc distance traveled. TIME TIME: Indcates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds). Yot can also program your monitor to count down from a set value by using...