Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
CATEYE STRADA WIRELESS CYCLOCOMPUTER CC-RD300W U.S. Pat. Nos. 5236759/6957926 Pat./Design Pat. Pending Copyright© 2007 CATEYE Co., Ltd. CCRD3W-070727 066600540 4 SENSOR ZONE 4 3 5 mm5 mm SENSOR ZONE 3 4 1 2 L mm 4 SENSOR ZONE 3 5 7 SENSOR ZONE 2 1 2 1 6 6 3 4 Click AC 1 2 3 4 km/h - mph Increase Move digits (by pressing & holding) Register the setting Register the setting Clear all data (initialization) Press the AC button on the back. Select the desired speed units Select “ ” or “ ”. Enter the tire circumference Enter the tire circumference of your bicycle in mm. * Refer to the tire circumference reference table. Set the clock When MODE is pressed and held, “Displayed time”, “Hour”, and “Minute” will appear, in this order. How to install the unit on your bicycle 24h - 12h, or increase the value Switch the screen or move digits (by pressing & holding) Register the setting (finish) Preparing the computer Measure wheel circumference (L) of your bike To get the most accurate calibration do a wheel roll out. W i t h t h e v a l v e s t e m perpendicular to the ground, mark the pavement at the valve stem. With the riders weight on the bike, roll the wheel one tire revolution in a straight line and mark the ground when the valve stem is perpendicular to the ground again. Measure the distance in millimeters. This is the most accurate wheel calibration number. 1Bracket band 2Bracket 3Speed sensor 4Magnet 5Sensor rubber pad 6Bracket rubber pad 7Nylon ties (x2) Battery case cover Push! When the computer is mounted on the bracket : Speed unit : Wheel size icon : Sensor signal reception icon WARNING / CAUTION • Do not concentrate on the computer while riding. Ride safely! • Install the magnet, sensor, and bracket securely. Check these periodically. • If a child swallows a battery, consult a doctor immediately. • Avoid having the computer in direct sunlight for unnecessary or extended periods. • Do not disassemble the computer. • Do not drop the computer. Doing so may result in a computer malfunction or damage. • When using the computer installed on the bracket, change the MODE by pressing on the three dots below the screen. Pressing hard on other areas can result in malfunction or damage to the computer. • Tighten the dial on the Flex-Tight bracket by hand only. Over-tightening can damage the bracket threads. • When cleaning the computer, bracket and sensor, do not use thinners, benzene, or alcohol. • Dispose of used batteries according to local regulations. • LCD screen may be distorted when viewed through polarized sunglass lenses. Wireless Sensor The sensor was designed to receive signals within a maximum range of 70 cm, to reduce chance of interference. When adjusting the wireless sensor, note the following: • Signals cannot be received if the distance between the sensor and the computer is too great. • The transmission distance may be shorter due to low temperature or low battery. • Signals can be received only when the back of the computer is facing the sensor. Interference may occur, resulting in incorrect data, if the computer is: • Near a TV, PC, radio, motor, or in a car or train. • Close to a railroad crossing, railway tracks, TV stations and/or radar base. • Using with other wireless devices in close proximity. Install the sensor and magnet Install the magnet C The clearance between the sensor surface and the magnet must not exceed 5 mm. B The magnet must pass through the sensor zone. A The distance between the computer and the sensor must not exceed the transmission range of 70 cm. The back of the computer must face the sensor. Install the sensor Sensor zone Inside of right front fork Inside of right front fork Max 70 cm YES! NO! Spoke Toward the sensor zone * Install the sensor as close to the upper part of the front fork as possible. Pull securely While supporting it by hand, push it out as if lifting the front up Handlebar Cut Caution: Make sure that the back of the computer faces the sensor. * The computer may not function appropriately on some stem if its back does not face the sensor as shown in A . When attaching the bracket to the handlebar When attaching the bracket to the stem Attach the bracket to the stem or handlebar Remove/install the computer Caution: Round off the cut edge of the bracket band to prevent injury. * After installation, rotate the front wheel gently to check that the speed is displayed on the computer. If the speed is not displayed, check that conditions A , B , and C , above, have been done appropriately. Stem ENG Before using the computer, please thoroughly read this manual and keep it for future reference. CC-RD300W Operating the computer [Measuring screen] MODE MODEMODE MENUMENU Pace arrow Indicates whether the current speed is faster ( ) or slower ( ) than the average speed. Tm Elapsed Time 0:00’00” - 9:59’59” Dst Trip Distance 0.00 - 999.99 km [mile] Dst2 Trip Distance-2 0.00 - 999.99 / 1000.0 - 9999.9 km [mile] Av Average Speed*2 0.0 - 105.9 km/h [0.0 - 65.9 mph] Mx Maxi...