Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Wireless Sensor The sensor was designed to receive signals within a limited range to prevent sensor signal interference. Thus, the sensor and computer must be relatively close. If the temperature or battery power is low, they may need to be even closer than normal. The sensor must be installed at the top of the fork, and the distance between the sensor and the computer should not exceed approximately 70 cm. Install the computer on the stem, with its bottom surface facing the sensor. (Take into account the angle of the stem.) Interference may occur, resulting in malfunction, if the computer is: • Near a TV, PC, radio, motor, or in a car or train. • Close to a railroad crossing, railway tracks, TV stations and or radar base. • Close to a second bicycle with wireless sensors. Correct installation of sensor and magnet A Attach the magnet 3 so that it passes through the sensor zone of the sensor 2. B Be sure to have a 5 mm-or-less clearance between the sensor 2 and magnet 3. Part names A B C D EF G Current Speed Sensor signal reception icon Flashes in sync with sensor signals. Sub measurement icon Pace arrow Indicates whether the current speed is faster or slower than the average speed. ( Faster Slower) Auto mode icon Speed unit Mode symbol .................................................................... b Indicates the mode currently selected. Tm (Tm 2) ............... [Elapsed Time] Dst (Dst 2) ............... [Trip Distance] Av (Av 2) .................. [Average Speed] Mx ............................ [Maximum Speed] Odo .......................... [Total Distance] ............................ [Clock] Wheel size icon H I J Backlight button Battery Case Cover Starting/Stopping measurement This computer allows automatic (Auto-mode) or manual measurement. During measurement, the speed unit icon flashes. The maximum speed and total distance will update, regardless of measurement. • Auto-mode (automatic measurement) If the icon is visible, measurement is automatic. In Auto-mode, starting/stopping measurement using the START/ STOP button is impossible. • Manual measurement If the icon does not light, starting/stopping the measurement using the START/STOP button is possible. * Use the menu screen to toggle between Auto-mode ON and OFF. For further information, see the MENU FLOW. Switching Mode symbol .................................... b Press the MODE button to switch measurement according to the OPERATION FLOW. Press the MODE button for 2 seconds to switch from Main to Sub measurement. • Sub measurement When Main measurement starts/stops, Sub measurement starts/ stops accordingly. Note, however, that the main and sub measurements must be reset individually. Resetting Main and Sub measurement at different times allows interval measurement to be carried out. * In the sub measurement the pace arrow compares the current speed to average speed 2. Resetting data ........................... Main : c Sub : d To reset measurement data, display the Main/Sub measurement data and press the START/STOP and MODE buttons simultaneously. Trip distance is not reset. Backlight Press the backlight button to illuminate the display for 3 seconds. If the battery is low, the wheel size icon flashes and the display does not illuminate. Power-saving function If the computer has not received a signal for 10 minutes, power- saving mode will activate and only the clock will be displayed. When the computer receives a sensor signal again, the measuring screen reappears. If two weeks’ inactivity elapses, power-saving mode will change to SLEEP mode. Pressing the MODE or START/STOP button in SLEEP mode brings up the measuring screen. Dual Wheel Size Two wheel sizes (Wheel sizes and ) can be registered on the computer. This is useful when the computer is shared between two bicycles or when one bicycle uses different wheel sizes at different times. Wheel size B has pre-programmed for a 26x1.95" size tire. * Use the menu screen to toggle between and . For further information, see the MENU FLOW. Changing the computer settings If the MENU button is pressed with the measuring screen displayed, the menu screen appears. Press the START/STOP button when measurement has stopped and no signal is being received to change menu settings. • Setting the clock Set the clock via Settings in the MENU FLOW. * For the Speed unit, reset Main and Sub measurement data before changing settings. * For further information, see the MENU FLOW. Maintenance To clean the computer or accessories, use diluted neutral detergent on a soft cloth, and then wipe it off with a dry cloth. Troubleshooting No display. Is battery in the computer run down? a ). Standard Parts #169-6590 Parts Kit #169-6580 Speed Sensor A #169-6570 Bracket kit #169-9691 Wheel Magnet #166-5150 Lithium Battery (CR2032) Option Parts #169-6667 Center Mount Kit #169-9760 Magnet for Composite Wheel #169-9690 Hi-Power Wheel Magnet ENG Replace it, and re-enter the correct information. (All Clear Incorrect data appe...