Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Or, "Setting Values Cross Reference Table" (page 19) can tell you the approximate wheel circumference according to the tire size. -2.Setting Speed Scale First, press the AC button; all displays illuminate and then "km/h" symbol appears. With each press of the right button, "km/h" and "mile/h" appears alternately. Select the desired scale and press the Set button to fix the scale. Fig.4 -3.Setting Wheel Circumference The preset value of this cyclocomputer is 2155mm (standard value for 700 x 32C wheel) (Fig. 5). When using 2155mm without revision, press Set button and this value is set. For revision, press the right button to increase the number and the left button to decrease, when the number is blinking. To increase/decrease the number rapidly, hold down the button. When the desired number appears, press the Set button and the value is set. -4.How to Reset or Change Wheel Circumference Get the stop state in O display, and press the Set button. The stored number flickers. Then revise the number according to the above. J Setting Clock Time Hold down the left button for about 2 seconds. Get the stop state by the press of right button. Then press the Set button; the digits for hours flicker. With each press of the right button, the digits increase by one. (To increase rapidly, hold down the button.) Then, press the left button and the digits for minutes flicker. After having increased the digits to the desired number, press the Set button, and the time is set. For accurate time setting, display the number which is 1 minute ahead of the present time; then at the tone of the time signal, press the Set button. L Fig.5 Fig.6 7 Fig.7 Magnet Sensor Band A Sensor Band B Spoke Fig.8 Rubber Pad Fig.7 Magnet Sensor Band A Sensor Band B Spoke Fig.8 Rubber Pad E Parallel Fig.9 2. Mounting to Bicycle • Attach the magnet on the right spokes of the front wheel. The spokes must run correctly through the inside of the magnet as in Fig. 7. • Attach the sensor with sensor bands A/B to the right fork. Choose a band that fits the fork diameter (S size for up to 24o, L for oversize). 1. Insert the band B into the slit of band A, and put the rubber pad inside of the band A (Fig. 8). Adjust the length in Marking Line of Sensor Front Fork Sensor order that the screw-fastening part of the bands are par- Band B Magnet allel when mounted to the fork (Fig. 9). Sensor *To pull out the band B from band A, tug strongly. 2. Mount the adjusted bands to the fork along with the sensor, by temporarily tightening the screw (Fig. 10). Center of the Magnet 3. Align the magnet's center and the sensor's marking line (Fig. 11), and make sure of 2mm clearance between the About magnet and sensor (Fig. 12). Then tighten the screw se- Sensor 2 mm Fig.10 Fig.11 Fig.12 Wire Fig.14 Bracket Rubber Pad Wire Securing Tape Fig.13 curely. Cut off the excess of sensor band B. • Secure the wire with tape as in Fig. 13. Wind the wire round the outer cable upto the handlebar. When adjusting the length, be careful that the wire will not hinder handlebar operation. • By using the rubber pad, attach the bracket close to the handlebar stem (Fig. 14). 8 Mounting Main Unit Lever Slide the main unit onto the bracket from front until it clicks into position. The contacts will E automatically connect. To remove the unit, pull it off forward while pushing down the lever (Fig. 15). Slide Test Mount the main unit. Spin the wheel to check if the sensor pulse symbol ( ) flashes. If not, adjust the relative positions of the magnet and sensor following the instructions. Fig.15 Front This completes the mounting process. Fig.16 3. Auto (Automatic Start/Stop) Function This function enables the main unit to start or stop automatically without operation of the right button, in which symbol appears on the screen (Fig. 16). How to Switch on/off Auto Function When the Set button is pressed in T, D or A mode, symbol appears and Auto function is on. To clear this function off, press SET button again and symbol disappears. • In this function, it starts/stops by perceiving revolutions of the wheel, so it stops measuring the elapsed time when the wheel ceases moving. • While this function is on, 2 seconds may be elapsed at the moment when the main unit is mounted onto the bracket. • When using this unit as an independent heart rate monitor apart from bicycle, switch off this function. Operation of the right (Start/Stop) button is needed. 4. Power Saving Function When the main unit is left without receiving any signal for about 60 minutes continuously, power supply is shut down and the unit will be in "sleep" state displaying only display (Fig. 17). By receiving signal from the wheel, or by a press of the right or left button, the unit "wakes up". Fig.17 9 Fig.20 Hook Hook E Wireless Heart Rate Sensor Main Unit Fig.18 Attachment Belt Fig.19 Electrode Belt Fig.21 Electrode Area How to Use as a Heart Rate Monitor When the wireless heart rate sensor is placed on your chest, the heart rate is measured....