Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn: CATEYE Customer Service Section Phone : (06)6719-6863 Fax : (06)6719-6033 E-mail : support@cateye.co.jp URL : Approx. 3.3 hours Before using the light, please thoroughly read this manual and keep it for future reference. Thank you for purchasing the CATEYE TRIPLE SHOT HL-EL 700RC. The Triple Shot light uses high-power white LEDs, and has a much longer operating life than other high-power rechargeable systems. COMPONENTS • Never short-circuit the terminals of the battery unit or the battery charger. It may cause the unit to overheat, resulting in fire or damage to the component. • Securely connect the plug so that the cable will not come unplugged or hinder your riding. • Never use damaged components (e.g., cables, etc.). Send any damaged components to our customer service department for repair. • The light unit may become extremely hot when on or immediately after it is turned off. Please use with caution. • Do not place it within children’s reach. • We recommend carrying a flashlight or spare battery unit with you in case the main battery dies. • Charge the battery unit before using because the unit self-discharges over time, decreasing its voltage. • Do not leave the battery overly discharged because it shortens the operating life of the battery. Try to charge the battery unit after each use. (“Overly discharged” refers to the state the battery is in when used over a period of time while below the specified cutoff voltage.) • If the lamp body or parts become dirty with mud, etc., clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. • Place the battery unit at least 10 cm away from any wireless meter, as transmitting and receiving performance may be adversely affected. • Never disassemble the light unit, battery unit, or battery charger. • This product is water-resistant under normal weather conditions of rain, etc. However, do not intentionally submerge it in water or allow rainwater to enter the battery bag. Connecting and Securing Cables 1. Align the male and female cable ends and connect them. Turn the plugs so that they are securely locked. Fix the cables to your frame and/or stem to keep them secured. CAUTION!: Pay attention to the arrangement of the cable so that it does not interfere with the handling of the bicycle. Do not secure the cable at an acute angle because the wire inside the cable may break. How to Charge Battery Unit HOW TO USE Switching on/off To switch the light on/off, press the button on the switch unit. FOR SAFE OPERATION INTRODUCTION The following spare parts are available. CAUTION!: Use only genuine spare parts from CATEYE. SPARE PARTS How to Adjust Beam Angle Adjust the beam angle downward so as not to blind oncoming traffic. It can also be adjusted 10 degrees to the left and right. 1. Remove the battery bag from your bicycle and open the bag. 2. Connect the jack to the battery charger. 3. Plug the battery charger to an AC outlet. NOTE: When charging is complete, the indicator light changes from flashing red to green. 4. When charging is complete, unplug the charging adapter. Refer to the figures below to rearrange the cable and use the seal strap to tightly close the opening. CAUTION!: When securing the battery to the frame, make sure the fixing strap attaches to the center of the battery unit. SPECIFICATIONS LIMITED WARRANTY Light Source ------------- Three High-Power White LEDs Battery Unit --------------- Nickel hydride battery (Ni-MH/12V 2700mAh) Battery Charger ---------- CHR-2700(AC100V-240V 50/60Hz 0.5A) Operating Time ---------- Approx. 3.3 hours Standard charging time - Approx. 3 hours Temperature range ------ Charging: -10°C - 40°C Operating: -15°C - 45°C Recharge/discharge number of times About 300 times (until the rated capacity drops to 50%) * The specifications and design are subject to change without notice. 2-year Warranty : Light/Switch Unit, Battery Unit, Battery Charger (Excluding degradation of the battery unit) If trouble or damage occurs during normal use, the product will be repaired or replaced free of charge. Type your name, address, date of purchase and the situation of trouble clearly on the warranty certificate, and send it back to the appropriate service center together with the product. Insurance, handling and transportation charges shall be borne by the customer. After being repaired or replaced, the product will be shipped back to the customer. Beam Adjustment Installing Bracket Attach bracket H31 or H32 to the handlebar. NOTE: Select H31 for oversized handlebars. 1. Mount a rubber pad and the bracket onto the handlebar. 2 thicknesses of rubber pads are supplied; if necessary, cut the rubber pad to fit. 2. Tighten and then close the lever to secure it. Make sure the bracket does not rotate on the handlebar. CAUTION!: Be sure to adjust the angle of the light’s beam by referring to the “Ho...