Оценок - , средний балл:
(
)
)
Производитель: Trek
Размер: 551.2 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Selecting the custom value 4-digit number There are two methods for Table 3- Custom wheel size codes selecting the custom wheel size value: • Select a value from Table 3, Custom wheel size codes. • Do a rollout test to measure the circumference of your wheel (page 24). To set the computer 1. Cycle Mode to TME. 00 x 20 2086 26 x .5 20 0 00 x 23 2096 26 x .90 2045 00 x 25 2 05 26 x .95 2050 00 x 28 2 36 26 x 2.0 2055 00 x 32 2 55 26 x 2. 2068 00 x 35 2 68 26 x 2.2 20 5 00 x 38 2 80 Custom 0000 - 2999 2. HoldSet• Wheel size appears. For 8i, Cycle Set• to the preferred Wheel Select icon for Wheel 1 or Wheel 2, and Push Mode to select. Setting Custom Wheel Size CLKTMEAVGMAXTRPODOMHMode Set Mode Set 3. Cycle Mode through the wheel sizes to the 4-digit number The left-hand digit flashes. The right-had digit changes. 4. PushSet• 5. Cycle Mode 6. Push Set• to select. The second digit flashes. 7. Repeat steps 5 and 6 to select all four wheel-size digits. 8. HoldSet• The computer returns to current speed. Setting Custom Wheel Size Figure 8- Measuring rollout for wheel size To measure rollout for wheel size Table 1 approximates the circumference of each tire size. Instead of using an approximation, you can measure the actual circumference of your wheel. You need a helper, your bike, and a smooth floor with enough room to roll the bike about 7 feet (245 cm) in a straight line. 1. With the valve stem of the front wheel directly over the floor Figure 18), sit on the bike. 2. Have your helper mark the floor at the valve stem. 3. While you sit on the bike, have the helper roll the bike forward one revolution of the wheel, so that the valve stem is again directly over the floor. 4. Mark the new location of the valve stem. 5. Measure the distance between the marks, in millimeters. If you can only measure in inches, convert to millimeters by multiplying by 25.4. 6. Use the result to program your computer, following the instructions on page 22. 24 Setting Custom Wheel Size lIMITEd WARRANTy Trek Bicycle Corporation warrants each new Incite computer against defects in workmanship and materials. This warranty covers Trek Incite computer models 6i, 8i, 9i, 11i, ACH, and ACH Digital for a period of two years from the date of sale. This warranty does not cover • Normal wear and tear, including the length of battery life • Improper assembly • Installation of parts or accessories not originally intended for, or compatible with the component as sold • Damage or failure due to accident, misuse, abuse, or neglect This warranty is void in its entirety by any modification of the component or its parts. This warranty is expressly limited to the repair or replacement of a defective item and is the sole remedy of the warranty. This warranty extends from the date of purchase, applies only to the original owner, and is not transferable. Trek is not responsible for incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. Claims under this warranty must be made through an authorized dealer. Proof of purchase is required. This warranty gives the consumer specific legal rights, and those rights may vary from place to place. This warranty does not affect the statutory rights of the consumer. Limited Warranty ...
Эта инструкция также подходит к моделям:Велосипеды - 6i (551.2 kb)