Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Once the pressure is set, you should ride the bike and fine tune the air pressure as needed. You have the pressure set properly when the shock doesn’t compress when you are sitting on the bike (unmoving), yet is about to start compressing—try bouncing a little. Now go for a ride up your favorite hill and notice what the shock does. If it pogos you should increase the shock air pressure slightly. The system is set perfectly when you get a soft ride, but no bounce on the climbs. Chapter 2: Set-up and Fitting Chapter 2: Set-up and FittingChapter 2: Set-up and FittingChapter 2: Set-up and FittingChapter 2: Set-up and FittingChapter 2: Set-up and Fitting Your VISION dealer will have put your recumbent together and set the adjustments for you. We don't recommend riding your VISION at all until the following procedures have been accomplished or checked by a qualified bicycle mechanic. We will review the fitting instructions here, and also point out some areas that need continuing inspection. The Handlebar The HandlebarThe HandlebarThe HandlebarThe HandlebarThe Handlebar Your VISION handlebar has been installed on your bike at the factory, but removed from the steerer (over-seat steering style) or the fork stem (below-seat style) for shipment. For over-seat steering models, insert the lower handlebar stem into the fork completely, align the stem plates parallel to the front wheel, and tighten the stem bolt to a torque specification of 65 in-lbs. Next, adjust the height of the bar at the sliding section. When you are comfortable with the height, make sure at least 3 inches of the lower riser are still in the upper riser, align the handlebars perpendicular to the front wheel, and tighten the riser clamp to 65 in-lbs. The above bar handlebar rotates forward for ease of entry and exit - it is meant to be pulled back tight against the fore/aft rest adjustment bolt under riding conditions. Set the bolt such that your elbows just rest against the seat sides when the handlebars are pulled against the stop. For below-seat steering models, insert the stem all the way into the fork tube, then back out the stem at least one quarter inch to prevent interference. Level the handlebar by sitting on the bike, turning the bars from side to side, and checking for seat/handlebar interference. Tighten the stem bolt and/or the binder bolt. Adjust the fore and aft position of the handlebars so that the handlebar grip is parallel or angled slightly downward from the seat frame. To check alignment, sit on the seat, grasp both handlebar grips firmly, and turn the handlebar side to side - there should be no interference between the seat frame and your arms. If there is, rotate the grips rearward in the stem. Tighten the stem binder. The bars should be tight enough that they will not rotate with 60lbs/27kg force on the handle, but not so tight that they will not rotate under a sharp blow (such as laying the bicycle on its side). Chapter 3: Chapter 3:Chapter 3:Chapter 3:Chapter 3:Chapter 3: (Continued) (Continued)(Continued)(Continued)(Continued)(Continued) line—and are sure you’re not about to take a long ride on a short pier—practice swinging your head to the left and right, taking quick glances behind you. The first time you do this you will inevitably shift your weight and hand position, causing the bike to swerve. Don’t panic, this is why we are practicing in the park instead of a congested street. While many riders like to use a helmet or bicycle mounted mirror—and we sell a beautiful unit that mounts onto the handlebar, see Chapter four of this manual—it’s important to be able to actually look around behind you. This not only gives you options on checking out traffic, but practicing this will increase your skills and confidence on the bike. At this point you should be feeling pretty good about life, zooming along nice and comfortable, relaxed and thinking about how much fun you are going to have on this thing. Well don’t get too cocky yet. Before you hit the open road there are a some more exercises you should do. Practice circling, both to the right and to the left. Start out with gentle curves, and progress to tighter and tighter radius “U” turns. You should really try to ...
Эта инструкция также подходит к моделям:Велосипеды - R40 (151.9 kb)
Велосипеды - R50 (151.9 kb)
Велосипеды - R54 (151.9 kb)
Велосипеды - R55 (151.9 kb)