Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Most adjustments are complete at this step. If brake still needs further adjustment, proceed to step 2 for rear brake. Assemb ly and Set-Up WARN ING : Failing to properly adjust and tighten the nuts and bolts that affix the forks can cause you to lose control and fall. Installing the Front Wheel 2 Slide axle through fork, spacer and wheel hub. When axle passes through the other side of the wheel hub, add the other spacer and slide though the fork. Secure with washer and nut. Note: Front axle is installed with the spacer between the fork and wheel for all Dirt Rockets. Note: If your model has one short spacer, it goes on the side of the hub with the disc brake. 1 Position wheel in front fork and slide disk brake into caliper. Turn power switch “OFF” before conducting any maintenance procedures. 3 With a 14mm and 17mm wrench tighten the front wheel screws. q Adjusting the Brakes Tools required: 5mm L-wrench q Chain and Tire Replacement Tools required: Phillips screwdriver and two (2) 19mm wrenches. 1 Loosen screw and remove chain guard. 2 Using two 19mm wrenches, loosen both axle nuts. 3 Push the chain tensioner down to loosen the chain and remove the chain from the wheel sprocket and motor sprocket. Push and remove the wheel downward. Note: Your hands will get greasy doing this. 4 Install the new chain or wheel by slipping the chain around the axle. Slide the axle into the slots on the frame. Slide the chain tensioner down and maneuver the chain onto the rear sprocket and front sprocket. 5 Re-attach the chain guard. Test ride and check. Readjust as needed. 6 q Replacing the Fuse Repair and Maintenance WARN ING : To prevent shock, please follow the instructions accordingly and do not skip any steps. 1 Remove the seat fairing to locate the 3 fuse boxes attached to the batteries. 2 Check all 3 fuses to see if the fuse(s) have burnt out. If the fuse(s) is(are) damaged, open the fuse cover. 3 Remove any fuse that is damaged or burnt out and replace with a new one of equal amperage. Note: Amperage is located on top of fuse. 3 Fuse boxes Fuse checking cavity Note: the arrangement of the hardware sequence: Right Side (Throttle) Nut Washer Spacer Left Side (Brake) Nut Washer Spacer Amperage number 7 Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at or call toll-free at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time. 4 Close the fuse cover and reattach the seat fairing. Repair and Maintenance qChecking Spoke Tension WARN ING : Regularly check the spoke tension and retighten the spokes whenever loose. If you have any doubt, ask an experienced motorcycle or bicycle mechanic to inspect your spokes to determine if the spokes need tightening or adjusting. Spoke Flange Spoke Nipple Hub Flange Spoke Flange Rim Nipple 2 1 4 3 28 27 1 Verify the spoke tension by shaking each spoke with your fingers. Spoke should not be loose from hub. Look for any play between where the spoke flanges attach to the hub. Try to turn the nipple using your fingers. You should not be able to spin any nipple by hand. If one or more spokes is loose, all spokes must be checked and need to be tightened with a spoke wrench. 2 Start with spoke closest to the tire valve stem and tighten each nipple, in sequence, exactly 1/4 to 1/2 turn. A single 1/4 to 1/2 turn may not be enough to bring the spokes into proper tension. Continue tightening all spokes no more than 1/2 turn in sequence until all spokes are tight. Note: More than a 1/2 turn each can cause the wheel to become distorted and wobbly thus permanently damaging the wheel. Repair and Maintenance q Chain and Sprocket The chain will typically have a “loose spot” and “tight spot” corresponding with a particular sprocket rotational position. This is normal and common to all chain-driven products due to run-out tolerances of the freewheel and sprocket. The chain should be adjusted to the ideal tension with chain in the tightest spot. Proper chain alignment must be maintained. The wheel must not be skewed. If the chain is noisy or rough running, check the lubrication, tension and alignment of the sprockets, in that order. q Battery Care and Disposal Do not store the battery in temperatures above 75° F or below -10° F. CONTAINS SEALED NON-SPILLABLE LEAD BATTERIES. BATTERIES MUST BE RECYCLED. Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an environmentally sound manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed lead-acid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is prohibited by law to throw away lead-acid batteries ...
Эта инструкция также подходит к моделям:Велосипеды - DIRT ROCKET MX650 (2.82 mb)