Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
* It is updated every 3 seconds, calculating from several times of the change in altitude and the trip distance. Slope update may be delayed. Abnormal data may also be temporarily displayed when speed quickly changes or during low-speed. Ascending altitude...Accumulation of ascent from the reset point to the current point is displayed. Total altitude gain ...The total altitude gain is displayed. Temperature...........The current temperature is displayed. * It is updated when the measurement screen is displayed (while measuring: every 3 seconds, while not riding: every 20 seconds). * The altitude measurement is updated every 3 seconds during measurement (when counting the elapsed time), but not updated when measurement stops. Caution: When Auto mode is Off, elapsed time counts even if the bicycle is not in motion. After measurement, be sure to press MODE and SSE simultaneously to stop measuring. Sea level altitude correction This unit determines the altitude by converting the change in atmospheric pressure and temperature; therefore, it may cause deviation from the actual sea level altitude. It is recommended to correct the sea level altitude just before measurement, using either the following methods. • ADJUST (sea level altitude correction): Enter the altitude at the current point. Enter the actual value at the point where the sea level altitude is known, such as along the seashore, or at a sign on the mountain, etc. * Press and hold MODE and SSE simultaneously on the setting screen to reset the corrected value to the default (a value according to ISO2533). • HOME (home altitude setting): Preset a specific sea level altitude. Preset the sea level altitude at your home in advance. Move to the HOME screen, and then return to the measuring screen by pressing MENU or the relevant shortcut. Then, the sea level altitude changes to the preset value. You can start with the correct sea level altitude by setting home altitude before stating from your home. * The sea level altitude is corrected on the menu screen “Sea level altitude correction”. Move to the sea level altitude correction screen by pressing MENU or the relevant shortcut from the measuring screen. Countdown distance Once the target trip distance is set, the unit displays the countdown distance to the target, and notifies at arrival. When the unit reaches the target distance, the countdown distance appears and the value flashes. The screen returns to the original display in 5 seconds. * The target distance is set on the menu screen “Countdown distance setting”. Move to the countdown distance setting screen by pressing MENU, MODE, or the relevant shortcut from the measuring screen. MODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMODEMENUMENUChanging the computer settings [Menu screen] Pressing MENU on the measuring screen moves to the menu screen for setup change. Once inside the menu screen, press the MODE button to scroll through setup items. Press MODE+SSE to enter the edit screens. Change cannot be done if there is an incoming signal and timer is active. Shortcut : When using a shortcut, the sea level altitude correction screen or the countdown distance setting screen is not displayed as shown in the figure below. It moves directly to the edit screen. After changing, be sure to press* MENU to register the setting. If the setting screen is not touched for a minute, the measur* ing screen appears without data changes. Setting change ( b y p r e s s i n g simultaneously)MODE+MODE+SSESea level altitude correction Countdown distance setting Wheel selection Wheel size entry Auto mode setting Clock setting Total distance manual entry Sensor ID setting Speed/temperature unit selection Menu screen Sea level altitude correction Shortcut A : MODE (By pressing & holding) > Back to the previous measuring screen ...................................Select ADJUST (sea level altitude correction) or HOME (home altitude setting) by pressing MODE. When MODE and SSE are pressed simultaneously,“+/- selection” or “Move digit” can be selected, and pressing MODE increases the +/-selection or the value. Enter the desired altitude. * For details, refer to “Sea level altitude correction”. Countdown distance setting Shortcut B : MODE (By pressing & holding) > Back to the previous measuring screen ................................Pressing MODE increases the value and pressing MODE and SSE simultaneously moves to the next digit. Wheel selection .....Toggle between the specified wheel size (tire circumference) and . Use this function if the computer is to be shared between two bicycles. Pressing MODE toggles between and . Wheel size entry ....Pressing MODE increases the value and pressing MODE and SSE simultaneously moves to the next digit. To enter the wheel size , display using “Wheel selection”. Auto mode setting...Press MODE to select ON or OFF. Clock setting...........Operate as described in “Preparing the computer 5”. Total distance manual entry ................
Эта инструкция также подходит к моделям:Велосипеды - CYCLOCOMPUTER CC-AT200W (725.77 kb)