Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
DO NOT USE IT ON STAIRS, ESCALATORS OR OTHER UNEVEN SURFACES. NEVER USE IT WITH INLINE OR ROLLER SKATES. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE AN ACCIDENT RESULTING IN SERIOUS INJURY. Bolt Bushing figure 3: To adjust stroller wheel tracking Installing Cover 1. At top of trailer frame, fit openings on cover sides around handle bar mounts. Fasten small buckle sections together. Adjust as needed. Photo 12 2. On trailer sides, join buckle sections on rear cover corners to buckle sections below side windows. 3. On trailer front, slip D-rings on front cover corners over hooked corners of tow bar mounts. Attaching Handle Slide handle into lower handle bar receivers and tighten knobs securely. To change height position, flip handle bar over. Photo 13 Installing Safety Flag Insert flag pole into hole in top of LEFT handle bar receiver. Photo 14 Trailer Front Opening Handlebar Mount Buckle PHOTO 12 Handle Bar Tighten Knob PHOTO 13: Tighten knob clockwise Inserting flag pole in handlebar receiver IMPORTANT DO NOT USE TRAILER WITHOUT SAFETY FLAG. PHOTO 14 Installing Seat Pads Match hook and loop fastening strips on trailer seat to back side of seat pad. Installing Shoulder Harness and Crotch Strap Pads Insert shoulder straps through loops on shoulder harness pads, with straps oriented so that FLAT sides of strap buckles face each other. Slide crotch strap through crotch strap pad. Photo 15 Using Seat Harness One Passenger: Note: In two-passenger trailers, use inner shoulder straps and crotch strap. 1. Place child in center of seat. 2. Snap shoulder straps into Y-buckle, with buckle positioned at child’s sternum. Adjust straps so that child cannot move too far forward in seat. 3. Fasten and adjust lap belt snugly. Figure 4 Two passengers: Note: For two children, use both shoulder harnesses and two outer crotch straps. 1. Seat first child on one side of seat. 2. Snap shoulder straps into Y-buckle, with buckle positioned at child’s sternum. Adjust straps so that child cannot move too far forward in seat. 3. Repeat for second child. 4. Fasten and adjust lap belt snugly. To remove children, release lap belt and harness buckles. Figure 5 Note: For taller children, the seat harness can be adjusted by moving the buckles on the shoulder strap webbing into the helmet pocket area, above the horizontal elastic. Harness Pads Flat sides of buckles facing each other Crotch Strap with Pad Seat Pad PHOTO 15 IMPORTANT SINGLE PASSENGER MUST BE SEATED IN CENTER POSITION. Harness Pads Lap Belt Figure 4 Harness Pads Harness Pads IMPORTANT DO NOT SLIDE SHOULDER STRAP ASSEMBLIES ABOVE WEBBING STOPS. WARNING ALWAYS SECURE CHILDREN WITH HARNESS AND LAP BELT BEFORE USE. ONLY USE THIS SEAT IF YOUR CHILD IS CAPABLE OF SITTING UPRIGHT ALONE. FAILURE TO DO SO COULD RESULT IN ACCIDENT AND SERIOUS INJURY OR DEATH. Outer Crotch Strap Outer Crotch Strap Lap Belt Figure 5 Using Seat Recliner For added comfort when children are sleeping, make the following adjustments to recline seat: 1. Loosen tension on lower horizontal strap on seat back. 2. Loosen tension on helmet pocket straps on upper back of seat. Photo 16 3. To return seat to upright position, reverse steps 1 & 2, and make sure upper seat strap is also tightened securely. Hitching Trailer to Your Bicycle Note: The Burley Forged Standard Hitch is used for bicycles with either nutted axles Figure 6 or quick release assemblies. Figures 7 & 8 1. Remove axle nut or rear quick release lever assembly from bike. 2. Match hole on flat side of hitch upper arm to left (non- chain ring side) rear dropout hole, and place hitch flat against the dropout. 3. Loosely reassemble axle nut or quick release assembly through hitch, dropout and wheel. Racks, bags, or fittings should not interfere with hitch. 4. Slide flex connector between hitch side arms, and match holes. 5. Open retaining pin and insert through hitch and flex connector holes from above. Close retaining pin. 6. Tighten axle nut or tighten and close quick release lever, with lever pointing to rear of bike. A properly adjusted quick release lever should leave an imprint on your palm when the lever is rotated to the closed position. Verify that hitch is secure and cannot be rotated by hand. 7. Wrap safety strap twice around inside of chain stay. Fasten hook to D-ring on underside of tow bar end. Figure 8 8. To remove trailer from bicycle, unfasten clip from D-ring and remove retaining pin. Loosen for Reclining Tighten to return seat to upright position IMPORTANT UPPER SEAT STRAP SHOULD ALWAYS BE TIGHTENED BEFORE TRAILERING. PHOTO 16 Nut Quick Release Hitch Nut Hitch Figure 7: Quick release assembly Figure 6: Nutted axle assembly Hitch Upper Arm Safety strap wrapped twice around chainstay Quick Release Lever Retaining Pin WARNING QUICK RELEASE LEVER MUST BE IN CLOSED POSITION AND HITCH SAFETY STRAP PROPERLY INSTALLED. NUTTED AXLES MUST BE TIGHTENED SECURELY. HITCH MUST NOT INTERFERE WITH RACKS, BAGS OR FITTINGS. INSPECT HITCH AND TOW BAR FREQUENT...
Эта инструкция также подходит к моделям:Велосипеды - d'lite ST (5.26 mb)