Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Verify left and right battery trays are installed on the correct sides. Not switching – auto-lens stays light and does not darken when welding or cutting. Stop welding or cutting immediately: Make sure the lens is turned On. If power is On, check the mode settings. Also review sensitivity recommendations and adjust sensitivity if possible. Clean lens cover and sensors of any obstructions. Make sure the sensors are facing the arc; angles of 45 or more may not allow the arc light to reach the sensors. Not Switching – auto-lens stays dark after the arc is extinguished, or the auto- lens stays dark when no arc is present. Reduce Sensitivity setting (see Section 3-5). In extreme light con- ditions, it may be necessary to reduce the surrounding light levels. If the lens remains dark, press the On-Off button to return lens to the clear state. Sections of the auto-lens are not going dark, distinct lines separate the light and dark areas. Stop welding or cutting immediately: The auto-lens may be cracked which can be caused by the impact of dropping the hel- met. Weld spatter on the auto lens may also cause cracking. (The lens may need to be replaced; most cracked lenses are not covered by warranty). Switching or Flickering – the auto-lens darkens then lightens while the welding or cutting arc is present. Review the sensitivity setting recommendations and increase the sensitivity if possible. Be sure the arc sensors are not being blocked from direct access to the arc light. Check the lens cover for dirt and spatter that may be blocking the arc sensors. Increasing Lens Delay 0.1 . 0.3 second may also reduce switching. Inconsistent or lighter auto-lens shading in the dark-state, noticeable on the outside edges and cor- ners. Referred to as an angle of view effect, auto-darkening lenses have an optimum viewing angle. The optimum viewing angle is perpendicular or 90 to the surface of the auto-lens. When that angle of view varies in the dark-state, welders may notice slightly lighter areas at the outside edges and the corners of the lens. This is normal and does not represent any health or safety hazard. This effect may also be more noticeable in applications where magnifying lenses are used. OM-234 388 Page 14 OM-234 388 Page 15 SECTION 10 . PARTS LIST 804 111 Miller 13 7 2 3 12 5 6 1 11 8 10 9 4 Figure 10-1. Digital Elite Auto-Darkening Welding Helmet Item Part No. No. Description Quantity Figure 10-1. Digital Elite Auto-Darkening Welding Helmet 1. . . . . . . . . . . . 216 331 . . . . . . . . Helmet Shell, Black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 . . . . . . . . . . . . 227 189 . . . . . . . . Helmet Shell, The Joker. . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1 . . . . . . . . . . . . 234 066 . . . . . . . . Helmet Shell, Stars And Stripes II. . . . . . . . . . . . . . . . . . . 1 1. . . . . . . . . . . . 223 454. . . . . . . . Helmet Shell, Inferno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 . . . . . . . . . . . . 216 327 . . . . . . . . Inside Lens Cover (4-1/4 X 2-1/2) (5 Per Pkg.) . . . . . . . . 1 3. . . . . . . . . . . . 234 760 . . . . . . . . Auto-darkening Lens Assembly . . . . . . . . . . . . . . . . . . . . 1 4 . . . . . . . . . . . . 216 337 . . . . . . . . Gasket, Front Lens . Cover . . . . . . . . . . . . . . . . . . . . . . . 1 5. . . . . . . . . . . . 234 758 . . . . . . . . Gasket, Auto-Darkening Lens Assembly. . . . . . . . . . . . . 1 6. . . . . . . . . . . . 216 326. . . . . . . . Outside Lens Cover (4-11/16 X 5-5/8) (5 Per Pkg.) . . . . 1 7. . . . . . . . . . . . 234 759. . . . . . . . Frame, Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 8 . . . . . . . . . . . . 770 246 . . . . . . . . Ratchet Headgear Assembly (Includes Items 9 And 10) 1 9. . . . . . . . . . . . 770 248* . . . . . . . Adjustment Angle/Stop Hardware Kit. . . . . . . . . . . . . . . . 1 10 . . . . . . . . . . . 770 249. . . . . . . . Fabric Headband . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . 079 975 . . . . . . . . Replacement O-rings For Kit 770 248 (5 Per Pkg.) . . . . 1 11 . . . . . . . . . . . 216 336. . . . . . . . Comfort Cushion, Foam Rubber. . . . . . . . . . . . . . . . . . . . 1 12 . . . . . . . . . . . 216 339 . . . . . . . . Battery Tray Kit (Left/Right) . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . 217 043 . . . . . . . . Battery,Lithium (CR2450) . . . . . . . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . . . . 222 003 . . . . . . . . Hard Hat Adapters (Not Shown) . . . . . . . . . . . . . . . . . . . . 1 13 . . . . . . . . . . . 770 250 . . . . . . . . Helmet Bag . Miller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . 212 235. . . . . . . . Lens, 0.75 Magnification (Not Shown) . . . . . . . . . . . . . . . 1 . . . . . . . . . . . . . . 212 236. . . . . . . . Lens, 1.00 Magnification (Not S...