Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Genuine Humminbird® accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird® product. NOTE: Your transducer may not look exactly like the transducer shown in the illustrations, but it will mount in exactly the same way. Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy -free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For complete details, see the Warranty section included in this manual. Contact our Customer Resource Center at either 1-800-633-1468 or visit our Web site at humminbird.com. Installation Overview Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird® accessory. If you find that any items are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our Web site at humminbird.com. In addition to the hardware supplied with your transducer, you will need various hand tools. Installation The trolling motor transducer is designed to mount on the trolling motor of your boat. All hardware needed for installation and operation of this Humminbird® accessory is either included with this accessory or came with your original transducer. The trolling motor mounted transducer allows you to gather sonar information from the point on the boat closest to where you are fishing. It is important that you properly orient the transducer housing in the direction of travel of the trolling motor, to ensure an accurate depiction of the terrain under your boat. The trolling motor mounted transducer will fit any standard trolling motor housing. Some users install this transducer in conjunction with a switch so that the standard transducer can be used for high-speed operation, and the trolling motor transducer can be used while trolling. 1. Attaching the Transducer WARNING! Before attaching the transducer to the trolling motor, confirm that the motor is disconnected from all sources of electrical power. CAUTION! Before attaching the transducer to the trolling motor, make sure the trolling motor is properly secured to the boat and will not shift during transducer installation. 1. Position the transducer on the underside of the motor housing. Refer to the illustration that most resembles your accessory, noting any requirements for directional bias. NOTE: Round, circular-bottomed transducers have no directional bias, and therefore orientation of these types of transducers is not as important. Rounded rectangular transducers, however, do have a directional bias, and must be installed as shown in the illustration. Side View of the Transducer Transducer should be mounted forward of the motor shaft. Styles of transducer may differ from illustration. 530511-3_A Trolling Motor Mount Installation Attaching the Transducer to the Trolling Motor NOTE: The transducers shown below have no directional bias. NOTE: The transducers shown below have a directional bias, and therefore need to be oriented according to the illustration below. Cable slots Tempprobe © 2011 Humminbird®, Eufaula AL, USA. All rights reserved. Trolling Motor Mounted Transducer 2. Insert the hose clamp through both openings on the top of the transducer and pull the two ends up around the motor housing. As you tighten the hose clamp, check to make sure that the transducer is properly aligned with the motor housing. 3. After tightening the hose clamp, make sure that the transducer is securely attached to the motor housing and will not slip off while in operation. 2.Routing the Cable The transducer cable has a low profile connector which must be routed to the point where the control head is mounted. There are several ways to route the transducer cable to the area where the control head will be installed. NOTE: Your boat may have a pre-existing wiring channel or conduit that you can use for the transducer cable. 1. Unplug the other end of the transducer cable from the control head. Make sure that the cable is long enough to accommodate the planned route. CAUTION! Do not cut or shorten the transducer cable, and try not to damage the cable insulation. Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' (15 m). For assistance, contact the Customer Resource Center at humminbird.com or call 1-800-633-1468 for more information. 2. Route the transducer cable around the side of the motor housing and secure it to the motor shaft using the plastic cable ties which have been provided. NOTE: As you route the cable from the trolling motor to the boa...