Оценок - , средний балл:
(
)
)
Производитель: Specialized
Размер: 3.2 mb
Название файла: 08Stump_SafireManual.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
10-12mm for 26” FSR 8.5-11mm for 29er FSR. See attached chart for starting air pressure. Note - the chart is only a starting point, actual sag needs to the checked and adjusted on the bike, while riding, and at regular intervals. Turn Brain Fade knob counter-clockwise (1 to 1.5 turns from full firm) to allow shock to sag more easily. After setting the pressure, push the rubber ring up to the seal, sit on the bike gently, dismount, and measure sag. AFR Brain Fade Compression setting: After the sag is set, adjust the Brain Fade to full firm or rider preference. AFR Brain Fade ride tips: Stumpjumper Brain Fade controls the Trail Tune inertia valve damping. The blue knob adjusts Trail Tune damping from firm (clockwise) to soft (counterclockwise) and does NOT completely lock out the shock (ie. Epic). Backing off from full firm can help with tracking in loose terrain conditions while riding off camber sections or climbing. The soft setting can also help during lengthy downhill or rugged conditions where the rider may want the suspension active at all times. Rebound setting: Set rebound damping adjuster to rider preference. A good starting point is 9 clicks out from full firm. Typically a slower rebound for slow speed, bigger hits to eliminate kickback, or faster rebound for higher speeds and smaller hits, so the suspension does not pack up and has time to rebound between bumps. NOTE: This air chart is designed as a recommended starting point only. Please refer to your shock owner’s manual for additonal setup information. DERAILLEUR GUARD INSTALLATION The Specialized Derailleur guard is available separately through your local Specialized dealer. The guard works with solid or Q/R axle types and is compatible with all Mountain bike models using the 2005-2006 Enduro/Demo derailleur hanger. Guard Part #: 9896-4030 Hanger Part #: 9895-4021 Short (10mm): (All Shimano derailleurs withoutcountersunk hanger bolt) Medium (25mm): Shimano XTR / XT / LX(All Shimano derailleurs with countersunk hanger bolt) Long (31mm): All SRAM derailleursGUARD PINS312510 Derailleur Guard Installation (Q/R option): 1. Install rear derailleur on derailleur hanger. 2. Place rear wheel in frame and install Q/R, with springs and without Q/R end nut. 3. Insert appropriate derailleur guard pin in derailleur. 4. Place guard sleeve in derailleur guard. 5. Slide derailleur guard and sleeve over guard pin and Q/R. 6. Install supplied Q/R nut and tighten Q/R. 7. Torque guard pinch bolt to 80 in-lbf (9 N-m). STUMPJUMPER / SAFIRE FSR CARBON INSTRUCTIONS The Specialized Stumpjumper Carbon frame utilizes advanced composite materials that require particular care during assembly, storage and riding. This installation and care guide contains instructions and warnings, plus torque specifications. Assembling a complete bicycle is a complicated task requiring training and experience, only a trained and experienced bicycle mechanic should install components to this frame. Reference should also be made to Barnett’s or some other comprehensive bicycle manual. WARNING! Failure to follow these instructions may result in a catastrophic failure of the frame and/or its components while riding, which may result in serious personal injury or death. WARNING! Bicycle assembly is an art which requires training and experience. Do not attempt installation of any component if you do not have experience and training as a bicycle mechanic. To ensure the best assembly possible and to prevent any damage to the components or frame, follow all torque specifications. Please refer to the specific owner’s manuals for mating component’s correct torque specifications. If the mating component’s recommended torque exceeds the frame’s recommended torque, use the lower torque spec. Due to torque considerations, not all components will be compatible. WARNING! Failure to follow the torque specifications in this installation guide will void your warranty, but most importantly may result in damage to the frame which may not be visible. If the frame is damaged, this can result in loss of structural integrity. Bicycle components such as a handlebar, handlebar stem, seat post, saddle, brakes, must be mutually compatible with each other, as well as the frame and the intended use. Any doubt regarding compatibility should be discussed with your local authorized Specialized retailer. WARNING! When placing the frame and/or bicycle in a repair stand, clamp the stand to the seat post and not the frame. Clamping the frame can cause damage to the frame that may or may not be visible, which may impair the structural integrity of the frame. SEAT POST Refer to your seat post owner’s manual prior to installation. Specialized Mountain frames have a 30.9mm seat post diameter and require that the seat post have a tolerance of 30.78mm to 30.95mm. Do not grease inside surface of carbon seat tube! The Stumpjumper Carbon frame uses a bolt-style seat post clamping mechanism. Since the components of this assembly are in di...