Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
Safety may be impaired if installation is not carried out in accordance with these instructions. . This appliance must be earthed. . Do not remove the screws from the earth tab extending from the oven mains terminal block (Fig. 8). . Before connecting the appliance make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This is situated on the front frame of the appliance and can be seen upon opening the door. . Do not alter the electrical circuitry of this appliance. THINGS TO NOTE . This appliance is designed to be fitted in cabinets of the recommended dimensions as shown (Fig.3 and 4) without any modification to the cabinet. . If your cabinet interior dimension is between 565570mm the oven may still be fitted. However, a minor modification to the cabinet will be required. . The dimensions given provide adequate air circulation around the unit within the cabinet, ensuring compliance with BS EN60-335. . Enquiries regarding the installation of the cooker point, if required, should be made to your Regional Electricity Company to ensure compliance with their regulations. . The appliance socket switch should be outside the cabinet but within 2m of the appliance to make it accessible to switch off the appliance in case of an emergency. . To protect the hands, wear gloves when lifting the oven into its housing. NOTE: HOUSE CIRCUIT Earth leakage and continuity tests must be carried out before the appliance is connected to the mains supply and re-checked after fitting. GETTING THINGS READY CHOICE OF ELECTRICAL CONNECTION . There are two possible ways to connect your appliance. Please choose from the most appropriate after reading the descriptions. a) It is recommended that this appliance is wired with suitably rating cable (min 13 A), into fixed wiring using a double pole isolator with a least 3mm contact separation in all poles and neutral, located within 2m of the appliance. If this fixed wiring circuit is only supplying the appliance, then a fuse of 13A (or circuit breaker) should be incorporated. When the circuit combines oven and hob, then wire and fuse fuse rating should be increased accordingly. Subject to Regional Electricity Companiesregulations if you wish to connect the ovenand hob to the power supply you may use one of the following two methods: b) If you wish to connect an oven and a hob to a cooker point you can: i. By connecting the appliance and hob separately to the cooker point. Oven and hob units should be separately connected to a control panel. In this case the appliance should be operated from 6mm. twin core, and earth, PVC insulated multicore cable. See Fig.1. Fig. 1 7 II. By connecting the cooker point to the hob and then connecting the hob to the oven. Provided that the hob manufacturer permits it, connect the oven to the hob to the cooker point using the same cabling as described in (a) above. Check the hob terminal block is large enough to take two cables and is of suitable rating. If not b) i) on page 7 must be used. See Fig.2. NOTE: 13 amp cable is not suitable for connecting this application. Fig. 2 NOTE: It is good practice to: . Fit an Earth Leakage Circuit Breaker to your house wiring . Wire your appliance to the latest IEE regulations. PREPARING CABINET FOR FITTING OF OVEN . Make sure the cabinet is the correct size for the appliance to be fitted (Ref. Fig. 3 and 4). . If the size is between 565-570mm, then the cabinet should be modified so that at the screw fixing points the recommended dimension of at least 560-565mm is maintained. The modification should ideally be localised to ensure that after screw fitment the oven is securely fixed into position. . The cabinet must be stable and level by firmly securing it to the wall or floor. If necessary, make arrangements to ensure the shelf upon which the oven will rest is level. RECOMMENDED CABINET DIMENSIONS (IN MILLIMETRES(IN MILLIMETRES) Fig.3 Built Under Installation 600 560 min 570 max 550 min 595 5 5 5 5 570 585 540 Cross section through cabinet showing oven positioned Cross section through cabinet showing oven positioned 570 600595 540 5 600 min 560 min 570 max 550 min 200 Recommended Fig.4 Built In Installation 9 HOW TO FINISH UNPACKING . Place appliance next to the cabinet in which it will be installed. . Remove the appliance packing except for bottom tray which should be left in position until the appliance is ready to be fitted into its cabinet. NOTE: It is imperative that the appliance is left in the base to protect both the appliance and the floor. . Ensure the owner is given these operating instructions. TOOLS REQUIRED The following tools will be needed and it helps to assemble them before starting to install your oven: A terminal screwdriver (3mm wide blade) A pozidrive screwdriver Pliers Wirestrippers Knife Sidecutters Adhesive tape Tape Measure MAKING THE ELECTRICAL CONNECTIONS Important: Switch off at mains, miniature circuit beaker and if appropriate, remove fuse befo...
Эта инструкция также подходит к моделям:Варочные панели - EOB 948 (487.37 kb)
Варочные панели - EOB 948 (487.37 kb)
Варочные панели - EOB 949 (487.37 kb)
Варочные панели - EOB 948 (487.37 kb)