Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Варочные панели - EC645PT90E/20 (3.83 mb)
Варочные панели - EC645PT90E/20 (2.56 mb)
Фрагмент инструкции
This is not a fault - this means that the safety device is no longer operating. Keep the burner as clean as possible. If the ignition sparkers are dirty they will not light properly. Clean them periodically using a small non-wire brush. Bear in mind that the ignition sparkers must not suffer any serious impacts. Cooking guidelines Burner Very high - High Medium Low Wok burner Boiling, steam-Reheating and keeping ing, griddling, things hot: cooked and pre- toasting, paellas, cooked dishes Asian food (wok). Rapid burner Escalopes, Rice, white Steaming: steaks, ome-sauce, ragout fish, vegetalettes, frying bles Semi-rapid Steamed pota-Reheating, keeping things burner toes, fresh vege-hot and making tasty cassetables, vegetable roles stews, pasta Auxiliary Cooking: casse-Defrosting Melting: but- burner roles, rice pud-and slow ter, choco ding, caramel cooking: veg-late, jelly etables, fruit and frozen products Timer The timer can be used in two ways: ¦ As a countdown timer. ¦ To programme the automatic off of up to two burners. Countdown timer The countdown timer can be used to time periods up to 99 minutes. This is independent of other services. It can be programmed even when the hob is switched off. This function does not switch off any burner. It is programmed as follows 1. Touch the 0 symbol once. The Q indicator lights up. The time programming indicator ‹‹ is displayed. 2. Touch the -or + symbol in the following five seconds to programme the required time. The countdown begins in a few seconds. The time programming indicator always displays the time remaining for the first programme to finish. When the programmed time has elapsed A beep sounds for 30 seconds. The time programming indicator ‹‹ is displayed. When any symbol is pressed the indicators go out and the beep stops. Change the programmed time Touch the 0 symbol and change the time using -or + in the following 5 seconds. The new programmed time will begin after a few seconds. To cancel the programme Touch the 0 symbol and change the time to ‹‹ using the -or + symbols. The indicator disappears following a few seconds or displays the time remaining for the following programme. Note: The countdown timer does not continue after a power failure. Programming a burner to switch off automatically Introduce a cooking time for the required burner. The burner turns off automatically when the programmed time is reached. Up to two burners can be programmed at the same time. It is programmed as follows The burner must be on. 1. Touch the 0 symbol twice. The indicators display the settings of the burners of their hob for one second. Select the desired burner by touching the 0 symbol. 2. Touch the -or + symbol in the following five seconds to programme the required time. The programme will start after a few seconds or when another burner is selected. This sequence may be used to programme any burner on the hob. The time programming indicator displays the time remaining for the first programme to finish. The burner indicator corresponding to the time lights up. The dimmed indicators correspond to other programmes that are in progress. Touch the 0 symbol to check all of the programmed times. When the programmed time has elapsed The burner goes out. A beep sounds for 30 seconds. The time programming indicator ‹‹. is displayed. The burner indicators flash successively. Then, when any symbol is pressed, the indicators go out and the beep stops. Turn the control knob of the burners switched off by the timer to the 0 setting. Change the programmed time Touch the 0 symbol, select the burner and change the time using the -or + in the following 5 seconds. The new programmed time will begin after a few seconds. Cancel the programme Touch the 0 symbol, select the burner and change the time to ‹‹ using the -or + symbols. The indicator disappears following a few seconds or displays the time remaining for the following programme. Notes ¦ The automatic off function does not continue after a power failure. ¦ It can be programmed for a duration of up to 99 minutes. Timer control panel block To activate the block: Press the symbols 0 and @ for 4 seconds. A whistle sounds and the display shows .–. Then the display will show the programme information again. If any symbol is touched while this function is being used a whistle will sound and .– will appear on display. To deactivate the block: Press the symbols 0 and @ for 4 seconds. Protection against overheating When high temperatures are reached in the electronics installation, the ”. message will alternate with information on the programmes in progress. The burners continue to operate. When the temperature drops to acceptable levels, the ”. message will disappear. If the temperature reaches the maximum level allowed, the timer turns off the burners and pauses the programmes in progress. The display alternates between the ”. message and the remaining times of the programmes. The control surfaces will remain blocked until the temperature...
Эта инструкция также подходит к моделям:Варочные панели - EC745RT90E/20 (2.13 mb)
Варочные панели - EC745RU90E/20 (2.13 mb)