Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Th e g uid elin e de te rmin es th e f ramework for th e re turn an d rec yc ling of us ed appliances as ap plicabl e. Tips for saving energy . Use pots or p ans w hic h a re th e ri ght size for eac h burn er. . A lways c entr e th e p ot or pa n over the burn er. . D o n ot cook w ithou t u sing a lid an d make su re the lid is properl y fit te d. Your new appliance Your new appliance and its accessories are described in this section. Gas wok . . . . Control knob The markings show the setting between high and low heat. The flame setting is infinitely variable between high and low. Special accessories You can order the following special accessories from your specialist dealer: AA 414 010 Ventilation molding for operation next to downdraft ventilation VL 414 WP 400 001 Multi-layer material wok pan, with curved base and handle, O 36 cm, 6 litres volume, 10 cm high. SV 401 090 Spindle extension up to 140 mm SV 401 205 Spindle extension up to 300 mm VA 420 000 Connection strip for combination with other Vario 400 appliances for flush installation VA 420 001 Connection strip for combination with other Vario 400 appliances for flush installation with appliance cover/ extension VA 420 010 Connection strip for combination with other Vario 400 appliances for surface installation VA 420 011 Connection strip for combination with other Vario 400 appliances for surface installation with appliance cover/ extension VA 440 010 Stainless steel appliance cover VA 450 400 Appliance extension, 38 cm Only use the accessories as specified. The manufacturer accepts no liability if these accessories are used incorrectly. 7 Burner assembly Always assemble the burner par ts correctly and evenly to avoid faults during ignition or during use. When assembling the burner parts, make sure that the burner head is placed on the base in such a way that the electrode is positioned in the opening on the burner head. The catching pin on the burner ring must fit in the corresponding groove on the burner head. Wok burner assembly Operation The markings show the position of the corresponding burner and the setting between high and low heat. The flame setting is infinitely variable between high and low heat. Notes . Only light a burner if the pan support and burner par ts are properly assembled. . Make sure the burners and electrodes are clean and dry. . Only use the recommended accessories. Do not cover the stainless steel cooktop base (e.g. with aluminium foil). . Do not cover the air inlet underneath the pan support. Caution! Heat damage to the extractor hood: Always switch on the extractor hood while the gas cooktop is in use. When using several cooking positions select a higher fan level on the extractor hood. Make sure there is a sufficient ventilation of the room. Switching on Your cooktop features automatic fast ignition. 1 Place a suitable pot or pan on the pan support. 2 Press down the control knob and turn it anticlockwise to the required position. The burner lights automatically. The flame size can be set continuously between high and low by slowly turning the control knob. Notes . When using large pots or pans you should ignite the burner in the low position. . Every time the gas hob is switched on, the electronics run an auto test. The electrode fires and the burner ignites after a few seconds. . When being switched on, a short sound may be heard when the electronics of the gas hob open the gas supply valve. This is normal. . The cooktop cannot be used during a power failure. Electronic flame detection and automatic re-ignition For your safety the cooktop features electronic flame monitoring. Should the flame go out during operation (e.g. because of a draught), the appliance will automatically re-ignite the burner. Should the re-ignition be unsuccessful (e.g. burner is soiled by spilled over food or liquid), the gas supply is switched off and a signal is sounded. The flashing indicator lights will go out except for the affected burner. This indicator will continue to flash for a few seconds. Turn the control knob to the OFF position. After the appliance has cooled down sufficiently, check this burner to see if all the burner parts have been assembled correctly. Check if the burner or the electrode has been soiled (see trouble shooting guide). Please note when switching on the cold appliance on the HIGH setting: Depending on the gas type and pressure, it is possible that the electrode continues to fire, although there is a flame visible, and then switches off. Turn the control knob to the OFF position and then to the LOW setting. Leave to warm up for 30 to 60 seconds after ignition. Then you can continue to use your appliance as usual. S w i t c hi ng of f Fully turn the control knob to the OFF position. The electronics of the appliance switches the gas supply off. a Risk of burns! When the appliance cover is closed, heat will accumulate. Only close the appliance cover when the appliance has cooled down....
Эта инструкция также подходит к моделям:Варочные панели - VG414110F/01 (1.01 mb)
Варочные панели - VG414210/01 (1.01 mb)