Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
If any bits are left (overcooked food, drops of grease etc.), however few, they will become stuck to the surface and more difficult to remove later. The holes and grooves must be clean for the flame to ignite properly. The movement of some pans may leave metal residue on the pan supports. Clean the burners and pan supports using soapy water and scrub with a non-wire brush. Alternatively, the pan supports can be put in the dishwasher. Use the dishwasher manufacturer's recommended detergent. If the pan supports are very dirty, they should be cleaned previously. Do not put the burner caps in the dishwasher. If the pan supports are fitted with rubber rests, ensure that these are also cleaned. The rests may come loose and the pan support may scratch the hob. Always dry the burners and pan supports completely. Water droplets or damp patches on the hob at the start of cooking may damage the enamel. After cleaning and drying the burners, make sure the burner covers are correctly placed on the burner flame diffuser. Unsuitable products Never slide pans across the glass surface, as you may scratch it. In addition, try not to drop heavy or sharp objects on the glass. Never strike any part of the hob. Do not use steam cleaners. This could damage the hob. Never use abrasive products, steel scourers, sharp implements, knives, etc. to remove bits of hardened food from the hob. If your hob is fitted with a glass or aluminium panel, never use a knife, scraper or similar to clean the point where it joins the metal. Do not use knives, scrapers or similar implements to clean the point where the glass meets the burner trims, the metal frames or the glass/aluminium panels, if fitted. Maintenance Always clean off any liquid as soon as it is spilt: you will save yourself any unnecessary effort. Grains of sand that may come from cleaning fruits and vegetables will scratch the glass surface. Melted sugar, or foods which contain a lot of sugar which may have spilt, should be cleaned off the hotplate immediately, using the glass scraper. Faults Sometimes certain faults detected can be easily resolved. Before calling the Technical Assistance Service, bear in mind the following advice: Fault Possible cause Solution The general electrical system is malfunctioning. Defective fuse. Check the fuse in the main fuse box and change it if it is damaged. The automatic safety switch or circuit breaker has tripped. Check the main control panel to see if the automatic safety switch or circuit breaker has tripped. The automatic switching on function does not work. There may be food or cleaning products stuck between the ignition sparkers and the burners. The space between the ignition sparker and the burner must be clean. The burners are wet. Dry the burner caps carefully. The burner caps are not correctly positioned. Check that the covers are correctly positioned. The appliance is not earthed, is poorly connected or the earthing is faulty. Contact the installation technician. The burner flame is not uniform. The burner components are not correctly positioned. Correctly place the parts on the appropriate burner. The grooves on the burner are dirty. Clean the grooves on the burner. The gas flow is not normal or there is no gas. The gas supply is blocked via intermediary valves. Open all gas taps. If the gas is supplied from a gas cylinder, check that this is not empty. Change the gas cylinder. The kitchen smells of gas. A gas tap has been left on. Turn off the taps. Incorrect coupling of gas cylinder. Check that the coupling is sound. Possible gas leak. Shut off the gas supply, ventilate the premises and immediately notify an authorised installation technician so that they can check and certify the installation. Do not use the appliance until you are sure that there is no gas leak in the installation or appliance itself. The burner immediately switches off after releasing the control knob. The control knob was not held down for long enough. The grooves on the burner are dirty. Once the burner is on, hold the control knob down a few seconds longer. Clean the grooves on the burner. Technical Assistance Service Warranty conditions When contacting our Technical Assistance Service, please provide the product number (E-Nr.) and production number (FD) of the appliance. This information is given on the...
Эта инструкция также подходит к моделям:Варочные панели - PRS926B90E/01 (3.5 mb)
Варочные панели - PRS926B90E/02 (3.5 mb)
Варочные панели - PRS926B90E/05 (3.5 mb)
Варочные панели - PRS926B90E/07 (3.5 mb)