2. Press the + or - symbol. The basic setting appears. + symbol: 10 minutes. - symbol: 5 minutes. 3. Set the desired time using the + or - symbols. After a few seconds, the time will start to elapse. Changing or cancelling the time Press the 0 symbol various times until the U indicator next to the U symbol lights up. Change the time or set to ‹‹ with the + or - symbols. Once the time has elapsed A warning signal sounds. ‹‹ is displayed on the time program function display. After 10 seconds the indicators turn off. Pressing the 0 symbol turns off the indicators and stops the beeping. Automatic time limitation If the hotplate remains in use for a long time and no changes When the control is turned to setting 0, the indicator goes off. are made in the settings, the automatic time limitation function The hotplate can now be reset. is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. The ” , ‰ symbol and the residual selected power level ( from 1 to 10 hours) . heat indicator • / oe flash alternatively in the display. Basic settings The device has several basic settings. These settings may be adapted to the user's individual needs. Indicator Function ™ ‚ Childproof lock ‹ Deactivated. * ‚ Activated. ™ . Audible signals ‹ Confirmation and error signals deactivated. ‚ Only error signal activated. . Only confirmation beep activated. „ All signals activated. * ™ † Automatic programming of cooking time ‹ Turned off. * ‚ - SS Automatic shut-off time *Factory settings Indicator Function ™ ‡ Duration of the time program function warning signal ‚ 10 seconds. * . 30 seconds. „ 1 minute. ™ ‹ Return to default settings ‹ Personal settings. * ‚ Return to factory settings. *Factory settings Accessing the basic settings 4. Then select the required setting with the + and - symbols. The hob should be turned off. 1. Select power level 1 on the front left-hand hotplate. 2. Within the next 10 seconds, press and hold the D symbol for 4 seconds approximately. In the display ™ and ‚ alternately light up and ‹ lights up as a default setting. 3. Press the Dsymbol several times until the desired function indicator appears. 5. Press the Dsymbol again for approximately 4 seconds. The settings should be correctly saved Exit the basic settings without changing them Switch off the hob and reset it. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cool enough before attempting to clean it. Only use cleaning products specifically designed for hobs. Follow the instructions provided on the packaging. Do not use: ¦ Undiluted washing- up liquid ¦ Dishwasher detergent ¦ Abrasive products ¦ Corrosive products such as oven sprays or stain removers ¦ Sponges that may scratch ¦ High-pressure or steam cleaners The best way to remove stubborn stains is to use a glass scraper. Follow the manufacturer's instructions. Suitable glass scrapers can be obtained through the Technical Assistance Service or from our online shop. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service you should bear in mind the following advice and warnings. Indicator Malfunction Solution none The electric power supply has been cut off. Use other electrical appliances to check whether there has been a power cut. The appliance has not been correctly con- Check that the appliance has been connected correctly according nected following the connection diagram. to the connection diagram. Electronic system malfunction. If none of the above checks resolve the malfunction, contact the Technical Assistance Service. The indicators The control panel is damp or an object is Dry the control panel area or remove the object. blink resting on it. “§ + number / s Electronic system malfunction. Unplug the hob from the mains. Wait about 30 seconds before + number / . + plugging it in again. * number ”‹ / ”S There is an internal operating error. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again. * ”./ ” † The electronic system has overheated and Turn the control to the 0 setting. Wait until the electronic system the corresponding hotplate has been has cooled down sufficiently before switching the hotplate back switched off. on. * ”… The electronic system has overheated and Turn the controls to the 0 setting. Wait until the electronic system all hotplates have been switched off. has cooled down sufficiently before switching it back on. * —‚ Supply voltage outside normal operating Contact your power company. limits. —. / — „ The hotpl...

Эта инструкция также подходит к моделям:
Варочные панели - NIV645B17M/01 (1.32 mb)
Варочные панели - NIV645B17E/01 (1.32 mb)
Варочные панели - NIV675B17E/01 (1.32 mb)