Оценок - , средний балл:
(
)
)
Производитель: Bosch
Размер: 692.21 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Old appliances are not worthless rubbish. Environmentally-conscious recycling can reclaim valuable raw materials. Before disposing of your old appliance, please make sure that it is unusable, or label it with a sticker stating „Caution, scrap”. Up-to-date information on how to dispose of your old appliance and the packaging from the new one can be obtained from your retailer or local authority. Before installation Transport damage Check the appliance after unpacking it. Do not connect the appliance if it has been damaged in transport. Electrical connection The cooker may only be connected by an approved specialist. Losses resulting from damage caused by incorrect connection will invalidate warranty claimes. Safety information The appliance should only be used for the preparation of food. The surfaces of heating and cooking appliances get hot during operation. Always keep children away from the appliance. Never place flammable objects onto the hot plates. Fire hazard! Never place cables of electronic devices onto the hot plates. The insulation on the leads could melt. There is a risk of short-circuiting. Do not use the appliance for heating. Ventilation Use of a gas cooking appliance results in heat and moisture generation in the room where it is set up. Make certain that the kitchen is well ventilated: keep the natural ventilation openings open or install a mechanical ventilation appliance (vapour exhaust hood). If you use the appliance intensively and for a long time, an additional ventilation may be necessary, for example by opening the window, or an increased output of the mechanical ventilation appliance if present. Never install gas appliances in vehicles. Burner lid Before using the hotplate burner, place the burner lid exactly. Operate the hotplate burner only when food to be cooked is placed on it. When using liquid gas (Propane/butane) make all connections between cylinder and appliance absolutely tight. Repairs Incorrectly done repairs are dangerous. There is a risk of electrocution. Repairs may only be carried out by after-sales service technicians who have been fully trained by BSH. In the case of a defect, switch off (or remove) the mains fuse in the building electrical system. Call the after-sales service. Reasons for damage Care and cleaning Do not use high-pressure cleaners or steam jets. Hotplates Keep an eye on pressure cookers during the heat-up phase. As soon as the proper cooking pressure is reached, reduce the heat setting. Please observe the separate operating instructions that came with your hob. The control panel Switches for hotplate D Switches for hotplate A Auxiliary burner B Normal burner C Normal burner DHigh-power burner A Switches for Switches for hotplate B hotplate C Before using your appliance for the first time Safety of the All hotplate burners are secured in such a way that the gas feed is interrupted when the flame is burners extinguished. This is done thermoelectrically. If the hotplate burners are on, there is a hissing noise. Cooking Selection of the cooking pots and their arrangement Correct! Always place pot in the middle of the hotplate burner. Use only pots and pans with a flat bottom. Select pot diameter to match the hotplate burner (see table). – low gas consumption – optimal cooking time –favourable arrangement Incorrect! Pot diameter too small. Hotplate burner flame burns beyond the bottom of the pots. Pot projects over the edge of the built-in hob. –High gas consumption – poor arrangement Burner Load in kW Pan base diameer Hob Ceramic hob High-speed burner Normal burner Simmer burner 2,85 1,85 1,10 2,90 1,70 1,00 240 bis 260 mm 200 bis 220 mm 120 bis 180 mm Igniting and regulating the burners Hotplate burner Igniting with the electric spark igniter Igniting with match or similar expedient The association of the operating elements knobs can be seen from the appliance description and recognized from the symbols on the gas cook screen. Igniting the burners is facilitated by an electric spark igniter. You can regulate infinitely between the high-power setting and low setting. g= large setting f= small setting 1. Press in the appropriate knob and turn anticlockwise to high setting. The electric spark ignition will operate as long as the knob is pressed in. 2. After igniting the flame, keep knob pressed in for around 5 seconds. 3. Before releasing, press knob vigorously once more. 4. If there is no ignition, or the flame goes out, repeat ignition procedure after around 3 seconds. 5. To switch off the burners, turn knob to the right to the zero setting. 1. Press in the appropriate knob, turn it anticlockwise to high setting and light the burner with a match. 2. Keep knob pressed in for around 5 seconds. 3. If the flame goes out, repeat ignition procedure after around 3 seconds. 4. To switch off the burners, turn knob to the right to the zero setting. Cleaning and Care Important cleaning For cleaning, do not use abrasives, no corrosive basics cleaners, and no sharp...