Оценок - , средний балл:
(
)
)
Производитель: Bosch
Размер: 324.6 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The › indicator lights up. The function has been turned on. To desactivate Press the › symbol. The › symbol switches off. The Powerboost function has been deactivated. Note: In certain circumstances, the Powerboost function may turn off automatically in order to protect the electronic components inside the hob. Automatic time limitation If the hotplate is used for prolonged periods and the settings are not adjusted, the automatic time limitation function is activated. The hotplate stops heating. The ” , ‰ ‹ symbol and the residual heat indicator • / oe flash alternatively in the display. When the control is turned to setting 0, the indicator goes off. The hotplate can now be reset. When the automatic time function is used, it is governed by the selected power level (from 1 to 10 hours) . Deactivating the warning signal A short beep sounds to confirm that a symbol has been touched. Depending on the model, this signal can be switched off. 1. Set the hotplates to the power level „ . 2. Switch the hotplates off individually, starting with the hotplate which is controlled by the knob on the right-hand side of the control panel. 3. Press and hold the › symbol corresponding to the left hotplate for at least 5 seconds. After 5 seconds has elapsed a beep will sound to confirm this. The warning signal can be reactivated. To do this, follow the same procedure as for deactivating the warning signal. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cold enough before attempting to clean it. Only use cleaning products specifically designed for glass- ceramic hobs. Follow the instructions provided on the packaging. Do not use: ¦ Abrasive products ¦ heavy-duty cleaners, like oven sprays and stain removers ¦ Pads that may scratch ¦ High- pressure or steam cleaners Glass scraper Remove dried-on food remains using a glass scraper. 1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. : Risk of injury!! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are usually due to small details. Before calling the Technical Assistance Service, you should consider the following advice and warnings. Indicator Malfunction Solution none The electric power supply has been cut off. Use other electrical appliances to check whether there has been a power cut. The appliance has not been correctly con- Check that the appliance has been connected correctly according to nected following the connection diagram. the connection diagram. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. “ flashes The control panel is damp or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Unplug the hob from the mains. Wait about 30 seconds before plug- s + number / ging it in again. * . + number ”‹ There is an internal error in the operation. Unplug the hob from the mains. Wait about 30 seconds before plugging it in again. * ” . The electronic system has overheated and Turn the control to the 0 setting. Wait until the electronic system has the corresponding hotplate has been cooled down sufficiently before switching the hotplate back on. * switched off. ”… The electronic system has overheated and Wait until the electronic system has cooled down sufficiently before all hotplates have been switched off. switching it back on. * ™‚ Supply voltage outside normal operating Please contact your local electricity company. limits. ™. / ™ „ The hotplate has overheated and has Wait until the electronic system has cooled down sufficiently before switched off in order to protect its cooking switching it back on. surface. * If the warning persists call the Technical Assistance Service. Do not rest hot pans on the control panel. Normal noise while the appliance is working Induction heating technology is based on the creation of electromagnetic fields that generate heat directly at the base of the pan. Depending on how the pan has been manufactured, these may produce certain noises or vibrations such as those described below: A deep humming sound as in a transformer This noise is produced when cooking on a high power level. It i...