Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Варочные панели - EH645TE11E/20 (2.63 mb)
Варочные панели - EH645TE11E/20 (359.24 kb)
Фрагмент инструкции
This function does not automatically switch off a hotplate. How to program 1. Press the 0 symbol several times until the W indicator lights up. ‹‹ appears in the time program function display. 2. Press the + or - symbol on the time program function. The basic setting will appear. + symbol: 10 minutes. - symbol: 05 minutes. 3. Set the time required using the + or - symbols. After a few seconds, the timer will start to count down. Once the time has elapsed A warning beep sounds. In the time program function display ‹‹ is shown, and the W indicator comes on. After 10 seconds the indicators turn off. Pressing the 0 symbol turns off the indicators and stops the beep. Changing or cancelling the time Press the 0 symbol several times until the W indicator lights up. Change the cooking time or set to ‹‹ with the symbols + or - , Automatic time limitation If the hotplate remains in use for a long time and no changes The indicator goes out when any symbol is pressed. The are made in the settings, the automatic time limitation function hotplate can now be reset. is triggered. When the automatic time function is used, it is governed by the The hotplate stops heating. On the hotplate display, ” and ‰ selected power level ( from 1 to 10 hours) . flash alternately. Basic settings The device has several basic settings. These settings may be adapted to the user's individual needs. Indicator Function ™ ‚ Childproof lock ‹ Deactivated. * ‚ Activated. ™ . Sound signals ‹ Confirmation beep and error signal deactivated. ‚ Only confirmation beep deactivated. . All signals activated. * ™ † Automatic timer ‹ Switched off. * ‚ - SS Automatic shut-off time *Factory settings Indicator Function ™ ‡ Duration of the time program function warning signal ‚ 10 seconds* . . 30 seconds. „ 1 minute. ™ . Power- Management function ‹ = Deactivated. * ‚ = 1,000 W. minimum power. ‚ = 1,500 W. . = 2,000 W. etc. S or S. = maximum power of the hob. ™ ‹ Return to basic settings ‹ Personal settings. * ‚ Return to factory settings. *Factory settings Accessing the basic settings 4. Then select the required setting using the + and - symbols. The hotplate must be off. 1. Switch on the hob. 2. In the following 10 seconds, press the @ symbol and hold it for 4 seconds. ™‚ appears on the left side of the screen, and ‹ on the right. 3. Press the @ symbol several times until the required function appears. 5. Press the @ symbol again and hold it for more than 4 seconds. The settings will have been correctly stored. Quit To leave the basic settings, turn off the hob at the main switch. Care and cleaning The advice and warnings contained in this section aim to guide you in cleaning and maintaining the hob, so that it is kept in the best possible condition Hob Cleaning Clean the hob after each use. This prevents food remains left on the surface from burning. Wait until the hob is cold enough before attempting to clean it. Only use cleaning products specifically designed for glass- ceramic hobs. Follow the instructions provided on the packaging. Do not use: ¦ Abrasive products ¦ heavy-duty cleaners, like oven sprays and stain removers ¦ Pads that may scratch ¦ High-pressure or steam cleaners Glass scraper Remove dried- on food remains using a glass scraper. 1. Release the scraper safety catch 2. Use the blade to clean the hob surface Do not attempt to clean the hob surface with the base of the scraper. This could result in scratching. a= Risk of injury! ! The blade is extremely sharp. Risk of cuts. Protect the blade when not in use. Replace the blade immediately when any imperfections are found. Care of the appliance Apply an additive to protect and preserve the hob. Follow the advice and warnings provided with the product. Hob frame In order to avoid damage to the hob frame, follow the indications below: ¦ Use only slightly soapy hot water ¦ Do not use sharp or abrasive products ¦ Do not use a glass scraper Fixing malfunctions Malfunctions are generally caused by minor faults. Before contacting the Technical Assistance Service, make sure you have read the following recommendations and warnings. Indicator Malfunction Measure none The electric power supply has been inter- Use other electrical appliances to check if there has been a power rupted. cut. The appliance has not been correctly con- Make sure that the appliance has been connected correctly. nected following the connection diagram. Electronic system malfunction. If in the above checks, the malfunction is not resolved, contact the Technical Assistance Service. “ flashing The control panel is wet or an object is Dry the control panel area or remove the object. resting on it. “§ + number / Electronic system malfunction. Disconnect the hob from the mains. Wait 30 seconds or so, then con- s + number / nect it again. * . + number ”‹ / ”S There is an internal error in the system. Disconnect the hob from the mains. Wait 30 seconds or so, then connect it again. * ” . The electronic system has overheated and Wait until t...
Эта инструкция также подходит к моделям:Варочные панели - EH651TE11E/20 (2.16 mb)
Варочные панели - EH651TE11X/20 (2.16 mb)
Варочные панели - EH811TL11E/20 (2.16 mb)
Варочные панели - EH845TL11E/20 (2.16 mb)