Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
• Insert the tabs on the back edge of the front end into the slots in the vehicle. 8 • Insert two 1/4" x 11/4" screws inside of the battery compartment and into the front end of the vehicle. Tighten the screws. Battery Compartment TOP VIEW Bumper Front End 9 RIGHT SIDE VIEW • Fit the bumper onto the front end. 7 • Insert two #8 x 3/4" screws through the front end and into the vehicle. Tighten the screws. 11H0440pr-0920 ASSEMBLY F ASSEMBLY F 10 Bumper • Insert seven #8 x 3/4" screws into the bumper and tighten. Grille • Insert two #8 x 3/4" screws the top of the grille. Tighten the screws. 12 11 Bumper Grille • Fit the grille onto the bumper. • Push down to fit the tabs on the grille into the slots in the bumper. 13 2524 • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustration. • For best results, avoid repositioning a label once it has been applied to the vehicle. 12 H0440pr-0920 ASSEMBLY F ASSEMBLY F 14 Headlights • Fit the headlights (left and right) onto the bumper. 15 Headlights • Insert two #8 x 3/4" screws into the top edge of each headlight. Tighten the screws. 16 Doors • Fit the door pegs onto the holes near the front end of the vehicle. Hint: There is a left and right door. They are designed to be assembled one way. 17 Plates • Fit the large hole on the plates to the door posts. • Align the holes in the plates with the holes in the top side of the vehicle. 13H0440pr-0920 ASSEMBLY F 18 20 Radio Connectors Dash Connectors Windshield/Dash • Insert three #8 x 3/4" screws into each plate and tighten. Motor Harness Connector Dash 19 Connector Front Radio Connector BACK VIEW • Separate the radio and dash connector wires from the motor harness connector. • Position the motor harness connector towards the front of the vehicle and into the battery compartment. • Position the dash connector and radio connector wires toward the back of the vehicle. • Open the doors on the vehicle. • Place the windshield/dash on top of the front end of the vehicle. • Plug both dash connectors together. • Plug both radio connectors together. Hint: If the connectors do not fit together, do not force them. Simply turn one of them over and try again! 21 • Fit the tabs on the windshield/dash into the slots in the front end of the vehicle. Windshield/ Dash FRONT VIEW 14 H0440pr-0920 ASSEMBLY F A B 22 24 • Turn the vehicle over. • Wipe the steering column with a paper towel to remove any excess lubricant. • First, insert the straight end of the steering column down through the hole in the metal bar A ; then through the hole in the vehicle Steering Column Metal Bar Hole BOTTOM VIEW Vehicle Hole floor B ; and finally, out through the hole in the dash. • Insert four #8 x 3/4" screws into the base of the windshield/dash. Tighten the screws. Steering 23 Dash DASH VIEW • Insert two #8 x 3/4" screws into the sides of the windshield/dash. Tighten the screws. • Close the doors on the vehicle. 25 • Insert the curved end of the steering column through the hole in the steering rod. Steering Rod Column H0440pr-0920 15 ASSEMBLY F 26 Assembly Tool 28 DASH VIEW • Insert a #6 x 11/2" screw into the hole in the base of the steering wheel. Tighten the screw. • Insert a #8-32 x 3/4" screw through the hole in the end of the steering column. • Attach a #8-32 lock nut (rounded side out) on the end of the screw. • While holding the lock nut with the open end of the assembly tool, tighten the screw with a Phillips screwdriver. • Turn the vehicle upright. Steering Wheel 27 Steering Column BACK VIEW • While supporting the steering column in place, fit the steering wheel onto the end of the steering column. Hint: You may need the help of another adult to hold the steering column in place while you attach the steering wheel. 29 • Insert and "snap" the key assembly into the slot in the dash. Key Assembly 16 H0440pr-0920 Hood Tab Slot Hood Tab Slot ASSEMBLY F Loosen These Screws DASH VIEW • Locate the FM Radio/Simulated CD Player/Digital Clock on the dash. • Loosen both screws in the battery compartment door. • Remove the battery compartment door. • Insert four, new "C" (LR14) alkaline batteries. Hint: We recommend using alkaline batteries for longer life. • Replace the battery compartment door and tighten the screws. • When sounds become faint or stop, it’s time for an adult to change the batteries! Please refer to page 27 for general information and tips for use of the FM Radio/Simulated CD Player. 30 Hood • Fit the long tabs on the hood into the slots in the front end of the vehicle. 1.5V x 4 "C" (LR14) Shown Actual Size Battery Safety Information In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated ...
Эта инструкция также подходит к моделям:Варочные панели - ESCALADE H044040 (1.01 mb)