Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
(MIN.) THK. FOR THE TOP AND SUPPORTING FRAME. SIDE ENCLOSURE TO BE AT LEAST 22 MSG MIN. THICKNESS. A REMOVABLE BOTTOM ENCLOSURE MUST BE PROVIDED UNDER EACH DROP-IN UNIT AND BE MADE OF METAL CONSTRUCTION OF AT LEAST 22 MSG MIN. IF VENTILATING OPENINGS ARE PROVIDED, IN THE BOTTOM ENCLOSURE, THEY MUST NOT ALLOW THE ENTRANCE OF A % IN. DIA. ROD NOR BE LOCATED DIRECTLY BELOW UNINSULATED LIVE TERMINALS, WIRING OR ELECTRICAL COMPONENTS AND SHOULD BE LOCATED AT LEAST 1 IN. AWAY FROM ANY INSULATED LIVE TERMINALS. C. \ Л "G" MIN. 'fbV WIRE GUIDE (PART OF I- CONTROL PANEL) | 1%" D'A. KNOCKOUT ALTERNATE LOCATION (SEE NOTE '3) 32%" MIN. - CG821 ¿-REMOVABLE BOTTOM ENCLOSURE - (METAL) • FURNISHED BY FIXTURE FABRICATOR. MINIMUM SPACING BETWEEN GRIDDLE TOP EDGE AND ADJACENT ITEMS SHOULD BE: FIXTURE BACK WALL - I*/*", FIXTURE SIDE ENCLOSURE - 1 ", FRONT CONTROL PANEL - V&", OTHER DROP-IN DEVICES - 1 CONTROLS SHALL BE MOUNTED ON THE FRONT VERTICAL SURFACE OF THE FIXTURE. FOR SUPPLY CONNECTIONS USE WIRES SUITABLE FOR AT LEAST 90°C (194°F). IMPORTANT STEPS IN INSTALLATION: REFER TO INSTALLATION MANUAL. GRIDDLE POSITION TO BE NO CLOSER THAN V* INCH FROM COMPONENT FRAME EDGE AND CONTROL PANEL INSTALL GASKET BETWEEN GRIDDLE TOP AND TABLE TOP BEFORE CLAMPING. EXERCISE CAUTION, SO THAT GRIDDLE TOP DOES NOT PINCH OR DAMAGE THE GASKET. WHEN “A” IS “B” “C” “D” “E” "F" “G” -js/a 7V4 ЗЭ/4 77/ie 2V32 23/в 9 23/e 8 4Уг 83/i6 225/32 31/б 93/4 31/8 8% 51/4 8is/16 317/Э2 37/в IOV2 37/e 9Vs 6 9iVie 49/32 45/0 111/4 45/e IOV4 6% IOV16 51/32 5э/в 12 - Dl».K*OC /— METAl FIXTURE j j (Br FABRICATOR) i ) в' Г Í ^ г~ i ) T 1 S i' 6| s r 1 Í ^_91 _ ^_ 9! m CG711 CG721 & CG821 CG SERIES DROP-IN ELECTRIC GRIDDLES NOTES: 1. GRIDDLE CAN BE MOUNTED WITH TROUGH IN THE FRONT OR REAR. DIMENSIONS SHOWN ARE FOR FRONT TROUGH MOUNTING, FOR REAR TROUGH MOUNTING THIS DIMENSION MUST BE BETWEEN V6" AND 2". TABLE TOP REINFORCEMENT AND GASKET FURNISHED BY HOBART (NOTE: GASKET IS SHIPPED IN GREASE TRAY.) ELECTRICAL CONNECTION BOX FACTORY LOCATED IN THE FRONT POSITION. CONNECTION BOX CAN BE MOVED TO REAR LOCATION SHOWN. 2. 3. IMPORTANT ANY DIMENSIONS SMALLER THAN THE MINIMUM OR LARGER THAN THE MAXIMUM SHOWN IN THE TABLE, WILL REQUIRE CORRESPONDING CHANGES BY THE FABRICATOR TO THE GREASE CHUTE BY ADDING AN EXTENSION, ETC. TO PREVENT THE GREASE FROM SPILLING INTO CABINET. ANY DIMENSIONS SMALLER THAN MINIMUM GIVEN, WILL REQUIRE ADDITIONAL PANELS ON SIDES AND BACK TO FACILITATE SERVICING. THE MINIMUM DIMENSION FROM THE BACK OF THE CONTROL PANEL, TO THE FRONT OF THE GRIDDLE TOP IS Va" REGARDLESS OF THE SHAPE OF THE BULLNOSE OR TABLE OVERHANG. GRIDDLES ARE SHIPPED FROM THE FACTORY WITH DIMENSION "D” AT 77/16". MOVABLE BRACES PERMIT THE FABRICATOR TO EASILY VARY THIS DIMENSION UP TO 107/16" IN INCREMENTS OF % INCH. THE MINIMUM SPACE BETWEEN ADJACENT HOBART GRIDDLES, MUST BE 15/,» AND BETWEEN ANY OTHER COMBINATION OF HOBART DROP-IN COOKING EQUIPMENT, MUST BE 1 ", ...
Эта инструкция также подходит к моделям:Варочные панели - CG721 (262.73 kb)
Варочные панели - CG711 (262.73 kb)
Варочные панели - CG731 (262.73 kb)
Варочные панели - CG831 (262.73 kb)