Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
This new carefully de-signed product, manu-factured with the highest quality materials, has been carefully tested to satisfy all your cooking demands.We would therefore request you to read and follow these easy instructions which will allow you to obtain ex-cellent results right from the start. May we wish you all the very best with your modern appliance! THE MANUFACTURER Instructions for use GB Installation All operations relative to installation (electric connection) should be carried out by skilled personnel in conformity with the rules in force. As for the specific instructions see part pertaining to installer. Use Heating elements - Manual control (Fig. 1-2) Rotate the knob concerned to the position correspondant to the needs of cooking taking into consideration that to a higher number a higher heat supply corresponds, see table “use of heating elements”. When pilot lights are lit, they indicate the top temperature at the indicated spot is higher than 50’ C. Some types of pilot lights will maintain some slight luminescence even after disconnection. That is quite normal. N.B. -When one makes use of heating elements, we advise receptacles with flat bottom (Fig. 3) having same diameter or lightly higher than that of the hot area. -Avoid overflows of liquid, therefore when boiling has happened, or in any case when liquid is heated, reduce the heat supply. -Don’t leave the heating elements on without receptades on the top or withvoid pots and pans. In the event of even a slight fracture on the cooking surface, disconnect the electric power supply immediately. Maintenance (Fig. 3) First of all remove stray food bits and grease drops from the cooking surface with the special scraper (fig. 4). Then clean the hot area as best as possible with SIDOL, STAHLFE or other similar products with a papertowel, then rinse again with water and dry with a dean cloth. Pieces of aluminum foil and plastic material whic have inadvertently melted or sugar remains or highly sacchariferous food have to be removed immediately from the hot cooking area with the special scraper (fig. 4) -This is to avoid any possible damage to the surface of the top. Under no circumstances should abrasive sponges or irritating chemical detergents be used such as oven sprays or spot removers. DO NOT USE STEAM CLEANERS Fig.1 NO NO YES Fig.2 USE OF THE HEATING ELEMENTS energy regulator intensita calore 1 - 2 Weak 3 - 4 Gentle 5 - 6 Slow 7 - 8 Medium 9 - 10 Strong 10 - 11 Bright Fig.3 GB .... Fig.4 Fig.4a Instructions for the installer GB Installation These Instrnctions are for the qualified technician, as a guide to the installation, adjustment and maintenance, according to the laws and standards in force. Any of these operations must always be canied out when the appliance has been disconnected from the electric system. Positioning (Fig. 4-4a) The appliance can be fitted into a working area as illustrated on the figure. Apply the seal supplied over the whole perimeter of the working area. Electrical connection (Fig. 5) Prior io carrying out the electrical connection, please ensure that: -the plant characteristics are such as to follow what is indicated on the matrix plate placed at the bottom of the working area; -that the plant is fitted with an efficient earth connection, following the standards and law provisions in force. The earth connection is compulsory in terms of the law. Should there be no cable andlor plug on the equipment, use suitable absorption material for the working temperature as well, as indicated on the matrix plate. Under no circumstance must the cable reach a temperature above 50°C of the ambient temperature. lf connecting directly to the mains power supply, fit a multi-pole switch of a suitable size for the rated capacity with a clearance distance which completely disconnects the power line under overvoltage category III conditions, consistently with the rules of installation (the yellow/green earth wire must not be interrupted). The plug or omnipolar switch must be easily reached on the installed equipment. N.B.: - The manufacturers dedine any responsibility in the event of non-compliance with what is described above and the accident prevention norms not being respected and followed. To avoid all risk,if the power cable becomes damaged, it must only be replaced by the manufacturer, by an authorised service centre, or by a qualified electrician. HEATING ELEMENTS V TYPE W REGULATION ~ 230 V single-circuit radiant single-circuit radiant O 145 1200 O 180 - O 195 1700-1900 energy regulator energy regulator 0+11 0+11 H05RR-F3x1.5Fig.5 Assistance Before contacting After-Sales Service: 1. See if you can solve the problem yourself. 2. Switch the appliance on again to see if the problem has been solved. if it has not, disconnect the appliance from the power supply and wait for about an hour before switching on again. 3. If the problem persists after this course of action, contact After-Sales Service. Specify: • the nature of the fault, •...