Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
HCG601 23 1 46 7 8 9HCG611 / HCG621 Igniting the Burners To ignite the burners, follow these instructions: 1. Lightly press the control knob (shown on the right) and turn the knob anti- clockwise to the maximum position. Press and hold the control down to begin the ignition process (a clicking sound will be heard). 2. Once the burner is lit, adjust the burner power to the required position. To turn the burner off, turn the knob clockwise past the maximum setting to the off position. Some models are fitted with a flame-failure device (designated by ‘F’ in model number). If your hob is fitted with such a device, hold down the control knob for a few seconds after ignition to allow the safety device to detect that the burner is lit. Flame-failure devices operate by shutting off the supply of gas to the burner in the event that the flame is extinguished accidentally. Please note: • The ignition device should not be operated for more than 15 seconds. • If a burner does not ignite, or turns off accidentally, turn the control knob to the ‘off’ position, and wait for one minute before attempting to reignite the burner. • If the burner does not ignite, repeat the ignition process with the burner at the minimum position. Efficient use of your Hob The hob is equipped with burners of different sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate burner depending on the size of the pan. The most efficient use of the hob is shown below, where the pan and burner are correctly chosen. Ensure that the pans do not overlap the edge of the pan stand, or cover the control panel. The table below shows the sizes of pan that should be used with each burner: Fig.2 Fig.3 Burner Size Auxiliary Semi-Rapid Rapid Triple Ring Wok Minimum Pan Diameter (cm) 12 16 20 24 - Maximum Pan Diameter (cm) 14 20 24 28 36 Correct use of the optional Wok Pan Adaptor The wok pan adaptor is a special stand that is designed to be fitted over the Triple Ring burner to give support to round bottomed woks. When using a wok, always place the wok pan adaptor in position over the pan support on the Triple Ring burner as shown in Fig.5. IMPORTANT: •The wok pan adaptor (Fig.5) must be placed over the pan support on the Triple Ring burner. •Do not use the wok pan adaptor for standard flat bottomed pans. Fig.4 Fig.5 Correct use of the optional Wok Pan Adaptor The wok pan adaptor is a special stand that is designed to be fitted over the Triple Ring burner to give support to round bottomed woks. When using a wok, always place the wok pan adaptor in position over the pan support on the Triple Ring burner as shown in Fig.5. IMPORTANT: •The wok pan adaptor (Fig.5) must be placed over the pan support on the Triple Ring burner. •Do not use the wok pan adaptor for standard flat bottomed pans. Fig.4 Fig.5 Care and Maintenance As the hob has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Over time with use, the stainless steel surface may discolour; this is normal and does not constitute a fault with this appliance. Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team for cleaning stainless steel surfaces. The enamelled parts of hobs are not suitable for cleaning in dishwashers; these should be washed by hand. IMPORTANT: • Steam cleaners must not be used when cleaning this appliance. • Ensure that all parts are correctly replaced after cleaning before attempting to use the hob. • After removing the pan stands, ensure the rubber pads are in place on the base of the pan stand before repositioning the pan stands straight and level on the hob. What to do if you smell gas: 1. Open doors and windows 2. Turn the gas supply off 3. Call Transco on : 0800 111 999 Burner Size Nominal Rating (kW) Simmer Rating (kW) Auxiliary 1.0 0.45 Semi-Rapid 1.75 0.6 Rapid 3.0 0.9 Triple Ring 3.3 1.6 Total rated gas input (HCG601) : 7.5kW Total rated gas input (HCG611) : 8kW Total rated gas input (HCG621) : 8.1kW Mains electrical voltage: 230 – 240Vac Total rated electrical consumption: <1W If your Hob is not working 1. Check that the mains supply has not been switched off. 2. Check that the fuse in the spur has not blown. 3. Ensure that the burner components are not excessively soiled as this can lead to ignition problems. Contact CDA Customer Care A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND P...
Эта инструкция также подходит к моделям:Варочные панели - HCG611 (534.5 kb)
Варочные панели - HCG621 (534.5 kb)