Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
For best results, only use pans with flat bottoms and choose an appropriate burner depending on the size of the pan. The most efficient use of the hob is shown below, where the pan and burner are correctly chosen. Ensure that the pans do not overlap the edge of the pan stand, or cover the control panel. The table below shows the sizes of pan that should be used with each burner: Fig.2 Fig.3 Burner Size Auxiliary Semi-Rapid Rapid Minimum Pan Diameter (cm) 12 16 20 Maximum Pan Diameter (cm) 14 20 24 Care and Maintenance As the hob has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Over time with use, the stainless steel surface may discolour; this is normal and does not constitute a fault with this appliance. Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team for cleaning stainless steel surfaces. The enamelled parts of hobs are not suitable for cleaning in dishwashers; these should be washed by hand. IMPORTANT: • Steam cleaners must not be used when cleaning this appliance. • Ensure that all parts are correctly replaced after cleaning before attempting to use the hob. • After removing the pan stands, ensure the rubber pads are in place on the base of the pan stand before repositioning the pan stands straight and level on the hob. What to do if you smell gas: 1. Open doors and windows 2. Turn the gas supply off 3. Call Transco on : 0800 111 999 Burner Size Nominal Rating Simmer Rating LPG Flow Rate (lh-1) (kW) (kW) G30 G31 Auxiliary 1.0 0.45 73 71 Semi-Rapid 1.75 0.6 127 125 Rapid 3.0 0.9 218 214 Total rated gas input : 7.5kW Mains electrical voltage: 230 – 240Vac Total rated electrical consumption: <1W If your Hob is not working 1. Check that the mains supply has not been switched off. 2. Check that the fuse in the spur has not blown. 3. Ensure that the burner components are not excessively soiled as this can lead to ignition problems. Contact CDA Customer Care A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. The wires in the mains lead of this appliance are coloured in accordance with the following code: Green & Yellow = Earth, Blue = Neutral, Brown = Live. As the colours of the wires in the mains lead for the appliance may not correspond with the coloured markings identifying the terminals connecting to the fuse spur, proceed as follows: • The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or coloured green. • The wire which is coloured blue must be connected to the terminal marked N (Neutral), or coloured black. • The wire which is coloured brown must be connected to the terminal marked L (Live), or coloured red. Note: Use a 3A Fuse Assembly and electrical connection should be carried out by specialised personnel. When installing this product we recommend you seek the help of another individual. DOUBLE POLE SWITCHED FUSE SPUR OUTLET USE A 3 AMP FUSE Gas Supply Requirements IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY A GAS SAFE REGISTERED FITTER OR OTHER SUITABLY QUALIFIED PERSON. • This installation must comply with the Gas Safety (installation and use) Regulations 1984. • This appliance is category II2H3+ and is designed for use in the UK and Ireland. The installation must comply with the Gas Safety (installation and use) Regulations 1984. • The CDA Group Ltd is not legally able to provide any assistance in the installation of gas appliances except to Gas Safe registered installers. Any Gas Safe registered fitter requiring help must provide their name, address and registration number. Information supplied will be validated before help is provided. • This appliance is suitable for conversion to Liquid Petroleum Gas (G30 or G31) or for natural gas (G20). A kit is provided. Do not attempt to fit the conversion kit yourself. • In the event that this appliance is not installed in accordance with the above requirements, the appliance may be disconnected from the mains gas supply until any faults are rectified; this is a legal requirement. • This appliance should be installed using 15mm copper pipe connected via a shut-off valve in an adjacent unit. The shut-off valve needs to be accessible in an emergency or for service purposes. • This appliance must not ...
Эта инструкция также подходит к моделям:Варочные панели - HCG501 (809.51 kb)
Варочные панели - HCG521 (809.51 kb)