Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HUMIDIFIER When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Always place this humidifier on a firm, flat and level surface. This humidifier may not work properly on an uneven surface. 2. Place this humidifier in an area where it is not accessible to children. 3. Do not place the humidifier near any heat sources such as stoves, radiators, and heaters. 4. Before using the humidifier, check the power cord for any signs of damage. If the cord is found to be damaged, DO NOT USE and return the humidifier to the manufacturer under the warranty agreement for repair. 5. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt too defeat this safety feature. 6. To disconnect the humidifier, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. Never pull by the cord. 7. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet. 8. The humidifier should always be unplugged and emptied when not in operation or while being serviced or cleaned. 9. Never tilt or attempt to move the humidifier while it is operating or filled with water. UNPLUG the humidifier before moving. 10. This humidifier requires regular cleaning. Refer to the CLEANING instructions provided. Never clean the humidifier in any manner other than as instructed in this manual. 11. Turn the humidifier OFF if the relative humidity exceeds 60%, or if you notice moisture on the inside of your windows. For proper humidity reading use a hygrometer, which is available in many hardware and department stores or by ordering one from the manufacturer (see Care Products). INTRODUCTION Thank you for purchasing a Duracraft® Natural Cool Moisture® humidifier. If you would like more information on our full line of products please visit our website at: HOW DOES IT WORK? Natural Cool Moisture® System The fan pulls dry air through a wet filter and releases invisible moisture into the air. When the unit is running you will not see or feel a “mist”. You will know your humidifier is putting moisture into the air as you watch the water level in your tank decrease throughout the day. The Duracraft® exclusive Automatic Moisture Balance System® increases moisture output when the air is dry and lowers the moisture output when the humidity level is high. This automatically helps to adjust the output for maximum comfort and helps prevent condensation. WHAT IS AgION™ ANTIMICROBIAL? Your DURACRAFT® Natural Cool Moisture® filter has been designed using new AgION™ technology which prevents the growth and migration of surface mold, mildew, fungus and odor causing bacteria in the filter for the filter’s life, approximately one season. Keep in mind, depending on your water quality, mineral deposits can still clog or discolor the filter and affect humidifier performance. MOTOR HOUSING MODEL DH-890 Your humidifier is made up of the following parts: NATURAL COOL MOISTURE® FILTER RINSE-TO-CLEAN® BASE FILL CAP WATER TANK High LowOff SET UP NOTE: We recommend that the humidifier be disinfected prior to first use. Please see CLEANING instructions. • Select a firm, level, flat location — at least six inches (15 cm) from any wall for proper air flow (Fig. 1). • Place the humidifier on a water-resistant surface, as water can damage furniture and some flooring. Duracraft® will not accept responsibility for property damage caused by water spillage. FILLING Fig. 1 Wall 6” Lift Fig. 2 Fig. 3 • Remove the water tank by grasping the handle and pulling straight up (Fig. 1). • Lift up on the Motor Housing to remove and set aside (Fig. 2). Remove the Natural Cool Moisture® filter from the base before filling the unit with water. Soak in a sink full of cool water to help reduce mineral build up and place back in the humidifier while wet. DO NOT SQUEEZE OR WRING OUT THE NATURAL COOL MOISTURE® FILTER. To help extend the life of your filter repeat this step each time you fill your humidifier. • Turn the water tank upside down so that the fill cap is facing up; unscrew the fill cap by turning it counter-clockwise and set aside. • Fill the water tank with COOL tap water (Fig. 3). Distilled water is not necessary as the water is filtered by the Natural Cool Moisture® filter. DO NOT USE HOT WATER. Doing so may damage the humidifier. • Replace the fill cap by turning it clockwise . DO NOT OVER TIGHTEN. Turn the water tank right-side up. FILLING CONTINUED NOTE:...