Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Its technology, design and operation and the fact that it exceeds the strictest quality standards, ensures it will give you full satisfaction for a very long time. Description A Spray button A B C D H I F E G Fig. 1 B Steam blast button C Steam setting control D Self-cleaning button E Spray nozzle F Filling hole G Base H Temperature gauge I Iron ready pilot light 23460_IM.indd2 22 23460_IM.indd 5/19/20105/19/2010 12:56:56 PM 12:56:56 PM Safety advice and warnings in the appliance. - Connect the appliance to a base with an earthed - Read these instructions carefully before switching socket rated at 16 amps. the appliance on and keep them for future consul- The appliance’s plug must fit into the mains tation. Failure to follow and observe these instrucsocket properly. Do not alter the plug. Do not use tions may result in an accident. plug adaptors. - Some parts of the iron have been lightly greased, - Do not use or store the appliance outdoors. so the iron may produce a little smoke when plugged in for the first time. This will stop after a Steam blast: short period of time. - Before using the iron for the first time, remove the Steam blasts give an extra steam jet to help remove plastic cover from the base and clean the base with tough creases. a soft cloth. - Select the maximum temperature*** on the tem- Pure wool fabrics (100%) can be ironed with the perature gauge (H). Wait for the pilot light to go off iron set to steam. Preferably chose a high steam (I). setting and use a dry ironing cloth. - Press the steam blast button (B). Wait some seconds until vapour penetrates the fibres before Use or working environment: pushing the button again. For optimum steam quality, do not apply more than three successive blasts. - Keep children and bystanders away when using The spray button has to be pressed repeatedly to this appliance. release the first spray. - The appliance must be used and placed on a flat, stable surface. Once you have finished using the appliance: Electrical safety: - Select the minimum position (MIN) using the thermostat control. - Fully unravel the power cable. - Unplug the appliance from the mains. - Always unplug the iron when not in use, even for a short period. Cleaning - Unplug the iron before filling or emptying the water tank. - Disconnect the appliance from the mains and al- Do not leave the appliance out in the rain or ex-low to cool before undertaking any cleaning task. posed to moisture. If water gets into the appliance, - Clean the equipment with a damp cloth with a few this will increase the risk of electric shock. drops of washing-up liquid and then dry. - Do not use the appliance if it has fallen on the - Do not use solvents, or products with an acid or floor, if there are visible signs of damage or if it has base pH such as bleach, or abrasive products, for a leak. cleaning the appliance. - Do not use the appliance near bathtubs, showers - Never submerge the appliance in water or any or swimming pools. other liquid or put it under running water. - Keep the appliance well away from heat sources, oil, sharp edges or moving parts. Damaged or tanSelf- cleaning function: gled cables increase the risk of electric shock. - Do not use the appliance if the cable or plug is - It is important to self-clean the appliance at least damaged. once a month to remove calcium and any other - Ensure that the voltage indicated on the namebuilt- up minerals inside the iron. plate matches the mains voltage before plugging - Fill the tank to the top. 23460_IM.indd3 33 23460_IM.indd 5/19/20105/19/2010 12:56:56 PM 12:56:56 PM -Stand the iron upright and press the plug it in. -Turn the temperature gauge to the ***position. -Let the iron heat up until the pilot light goes off and comes back on again. -Unplug the iron and place it over the sink. -Push the self-cleaning button (D) and keep it pushed down. -Let the water flow out through the steam vents in the base, while lightly shaking the iron. -Release the self-cleaning button after a moment or when the tank has emptied and place the iron in an upright position. -Let the iron cool and then clean it. Anomalies and repair Go to an authorized Technical Support Service in the event of malfunctions. Do not try to dismantle or repair the iron yourself, as this may be dangerous. If the connection to the mains has been damaged, it must be replaced, and you should proceed as you would in the case of damage. Ecology and recyclability of the product -The materials of which the packaging of this appliance consists are included in a collection, classification and recycling system. Should you wish to dispose of them, use the appropriate public containers for each type of material. -The product does not contain concentrations of substances which could be considered harmful to the environment. -Should you wish to dispose of the product once its working life has ended, take it to an authorised waste agent for the selective collection of waste from electric and electronic ...