Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
The packing materials used for this appliance are part of a pick-up, sorting and recycling system. If you wish to discard them, please use the public containers provided for each kind of material. Description A Iron on/off switch. B Boiler on/off switch. C Boiler operation LED. D Iron operation LED. E Steam pressure indicator LED. F Water filling cap. G Mains connexion. H Iron steam switch. I Steam switch control (depending on the model). J Iron thermostat control. K Iron thermostat LED. H B E F C I J A D K L G L Iron housing. MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd2 22 MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 7/15/20097/15/2009 4:32:44 PM 4:32:44 PM Fig. 3 Fig. 2Fig. 1 Fig. 4 Fig. 5Fig. 6 MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd3 33 MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 7/15/20097/15/2009 4:32:44 PM 4:32:44 PM Tips and safety warnings -Please read these instructions carefully before using the appliance and keep them for future reference. -Unpack the appliance and check it is in perfect condition and working order, as any factory fault or damage caused by transport is covered by the MELLERWARE guarantee. -This device has been designed for household use, not for commercial use. -Do not leave the appliance without supervision if you are not going to use it immediately. This will save energy and prolong the working life of the appliance. -Keep the appliance out of the reach of children. -The appliance must not be connected to the mains while the boiler is being filled (Fig. 1). -Before connecting the appliance to the mains, ensure the supply voltage is the same as that marked on the appliance. English -The water filling inlet must not be open during operation. -This appliance must be connected to an electrical socket with an earth connection. -Any improper use or failure to comply with the instructions for use will invalidate the warranty and free the manufacturer from any liability concerning the appliance. -IF THE IRON IS IN ITS HOUSING AT MAXIMUM TEMPERATURE FOR A LONG TIME, THIS MAY CAUSE ALTERATIONS TO ITS COLOUR, BUT THIS HAS NO EFFECT ON THE PROPER OPERATION OF THE APPLIANCE. -The appliance must be used and placed on a flat, stable surface -When placing the appliance on its support, make sure the surface on which the support is fitted is stable. -Do not use the appliance if it has been dropped, if there are visible signs of damage or if it leaks. Before using the appliance for the first time This professional iron works with tap water. However, the use of distilled water is recomended in areas with a high lime level in the water. Some parts of the iron have been slightly greased. They can therefore give off steam on first use, but this steam will disappear after a short time. Practical tips -Keep the sole plate smooth, do not apply it to metallic objects (i.e., to the ironing-board, butons, zips...). -Fit the iron in its housing (L) for transport and storage, in order to improve its stability. -To avoid burns, do not lean Bravissimo 2 Pro’s iron on its back. Steam ironing When you start to iron, proceed as follows: -Unscrew the cap (F) and fill the boiler with water, using a jug (Fig. 1) (if you fill it with hot water, the appliance will be ready for use sooner). -Even if the boiler has a certain level of water, it is always recommended to fill it to the top for a longer range, thanks to its large 1l capacity. -Carefully close the cap (F), screwing it to the end. -Place the boiler on a flat , stable surface. -Plug the appliance into the mains. -Switch on the boiler and the iron by pressing the relevant switches (B) and (A). The corresponding LEDs will light (Fig. 2). Thermostat Type of Steam control fabric position • No No Nylon / Silk Wool Cotton, Linen Yes It is recommended not to use steam in the • and •• thermostat positions, as water could drip. MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd4 44 MW_EX_23810_BRAVISSIMO_PRO 2_IM.indd 7/15/20097/15/2009 4:32:44 PM 4:32:44 PM -Set the desired temperature with the thermostat control (J), depending on the type of cloth to be ironed (Fig. 3). -The appliance will be ready for use when the pressure indicator LED (E) lights up (Fig. 4). While ironing, this LED (E) goes on and off automatically, this is normal. -By pressing the steam switch (H) you will get a constant steam jet (Fig. 5). The steam stops when you release the switch. How to fill the boiler while ironing To fill the boiler, proceed as follows: -Eliminate steam pressure from inside the boiler by switching on the steam switch (H) (Fig. 5). -Turn off the boiler (B) and iron (A) switches. -Unplug the appliance from the mains. -Carefully unscrew the cap (F) to let the residual steam out of the boiler. -Wait for some minutes and carefully pour 1l of water into the boiler using a jug (Fig. 1). -Carefully close the cap (F) again, screwing it to the end. Vertical ironing It is possible to iron hanging curtains, garments on their own hangers... (Fig.6) -Adjust the iron thermostat control (J) to the maximum temperature. -Iron f...