Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Use appliance only for its intended use. 2. To protect against a risk of electric shock, do not immerse the appliance in water or other liquids. 3. The appliance should always be turned to Minimum (Min) before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let appliance cool completely before putting away. Loop cord loosely around appliance when storing. 5. Always disconnect appliance from electrical outlet when filling appliance with water or emptying appliance when not in use. 6. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the appliance ship it to the nearest authorized Rowenta Appliance Service Center for examination and repair. Incorrect reassembly can cause a risk of electric shock when the appliance is used. 7. Close supervision is necessary for any appliance being used by or near children. Do not leave appliance unattended while plugged in or on ironing board. 8. Burns can occur from touching hot metal parts, hot water steam or hot soleplate cover. Use caution when you turn a steam iron upside down. There may be hot water in the reservoir. 9. The use of accessory attachments is not recommended by Rowenta and may result in fire, electric shock or personal injury. SPECIAL INSTRUCTIONS 1. This is a 1400 watt appliance. To avoid a circuit overload, do not operate a high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 12- ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. 3. Your Rowenta appliance is intended for household use only. SAVE THESE INSTRUCTIONS BEFORE USE M Please read the instructions for use and the Important Safeguards carefully. M Remove the sticker or transparent soleplate protector. M It is normal for a small amount of smoke to be produced the first time the iron is used. This will quickly disappear. 1 3-WAY AUTO-OFF If the iron is not moved while it is plugged in, an internal safety switch will turn it off. It will turn off in 8 minutes if left vertically or in 30 seconds if left on its soleplate or tipped over. A red flashing light indicates that the auto-off has been activated. To switch the iron on again, move the iron or gently shake it. Wait until iron is fully reheated before use. Auto-off is not an on/off switch. Always unplug the iron when it is not in use. 2 STEAM IRONING Filling with water M Ensure the iron is unplugged. M Slide the variable steam control completely to the left. M Hold the appliance upright so that the water inlet is horizontal. M Fill with water (containing no additives) to the max. water level mark. Adding water M If you need to add water during ironing UNPLUG the iron and repeat above steps. M Ensure iron is fully reheated after filling (pilot light goes out) before ironing. M To avoid damage to clothes from dust or dirt that may collect in the iron, we recommend that for the first use or after the iron has been stored for some time that you first iron an old cloth that can be discarded, testing both the steam and burst of steam features. 3 SELECTING THE TEMPERATURE Set the temperature control dial according to the type of fabric you are ironing. Check the fabric's label for appropriate setting. VERTICAL 30 sec. 8 min. 30 sec. VERTICAL 1 2 min 3 Laundry label Fabric Temperature setting Synthetics Nylon Polyester l (low temperature) Silk Wool ll (medium temperature) Cotton Linen lll (high temperature) . To avoid an automatic switch off while the iron is heating up, always keep the iron on its heel. . Start at a low temperature and graduate to a high temperature. . For delicate fabrics we recommend carrying out a test on an unobtrusive part of the garment (inner seam). . Steam can only be produced when the thermostat is in the red cotton/linen zone. SETTING THE VARIABLE STEAM CONTROL min max CleanSelf 4 Set the variable steam control to required steam volume. Steam can only be produced when the thermostat is aligned to lll (red zone on dial). (If on setting l or ll the variable steam lever should be shut off.) Allow iron to heat up (light goes out) before activating the steam control. Iron ready for steam ironing Steam is produced as soon as the iron is held horizontally and variable steam lever is moved from the min position. Steam off Steam generation can be interrupted by standing the iron on its heel or sliding the variable steam control fully to the left (min.) ANTI-DRIP SYSTEM (Depending on model) In order to produce steam, all irons require a high temperature. If the soleplate is not hot enough some of the water will not turn to steam and can spit or leak from soleplate. The anti- drip system automatically reduces the volume of steam when ironing at low temperatures to prevent dripping...