Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Use iron only for its intended use. 2. To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3. The iron should always be turned to Minimum (Min) before plugging or unplugging from outlet. Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect. 4. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5. Always disconnect iron from electrical outlet when filling iron with water, emptying iron or when not in use. 6. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron, ship it to the nearest authorized Rowenta Appliance Service Center for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7. Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while plugged in or on an ironing board. 8. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron upside down there may be hot water in the reservoir. 9. The use of accessory attachments is not recommended by Rowenta Appliance Company and may result in fire, electric shock or personal injury. SPECIAL INSTRUCTIONS 1. This is a 1400 watt appliance. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 2. If an extension cord is absolutely necessary, a 12-ampere cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over. 3. Your Rowenta appliance is intended for household use only. SAVE THESE INSTRUCTIONS L MN K J GHEF A B I C/D L MN K J GHEF A B I C/D Description: A Spray nozzle B Covered water filling inlet C Variable steam control D Self clean system E Spray button F Burst of steam button G Auto-off indicator light H Temperature control dial I Swiveling cord protector J Supply cord K Temperature light L Transparent water tank M Stainless steel soleplate (Airglide, Precision or Laser depending on model) N Water level indicator 5 BEFORE USE Please read the instructions for use and the Important Safeguards carefully. Remove the transparent soleplate protector. It is normal for a small amount of smoke to be produced the first time the iron is used. This will quickly disappear. 3-WAY AUTO-OFF If the iron is not moved while it is plugged in, an internal safety switch will turn it off. It will turn off in 8 minutes if left vertically or in 30 seconds if left on its soleplate or tipped over. A red flashing light indicates that the auto-off has been activated. To switch the iron on again, move the iron or gently shake it. Wait until iron is fully reheated before use. STEAM IRONING Filling with water Ensure the iron is unplugged. Slide the variable steam control completely to the left. Hold the appliance upright. Slide the cover of the water filling inlet open. Fill the iron with tap water to the maximum level mark (see water usage for more information). Adding water If you need to add water during ironing. UNPLUG the iron and repeat above steps. Ensure iron is fully reheated after filling (temperature indicator light goes out) before ironing. To avoid damage to clothes from dust or dirt that may collect in the iron, we recommend that for the first use or after the iron has been stored for some time that you first iron an old cloth, testing both the steam and burst of steam feature. Clean min max Self 30 sec. 8 min. 30 sec. LONG-LIFEANTICALC LONG-LIFEANTICALC SELECTING THE TEMPERATURE SELECTING THE TEMPERATURE Set the temperature control dial according to the type of fabric you are ironing. Check the fabric's label for appropriate setting. Laundry label Fabric Temperature setting synthetics e.g. viscose, polyester silk, wool cotton, linen To avoid an automatic switch off while the iron is heating up, always keep the iron on its heel. Start at low temperature and graduate to high temperature . For delicate fabrics we recommend carrying out a test on an unobstrusive part of the garment (inner seam). Steam can only be produced when the thermostat is in the red cotton/linen zone. SETTING VARIABLE STEAM CONTROL Set the variable steam control to required steam volume. Steam can only be produced when the thermostat is aligned to or max. (red zone). Allow iron to heat up (light goes out) before activating the variable steam control. Iron ready for steam ironing Steam is produced as soon as the iron is held horizontally. Steam off Steam generation can be interrupted by standing the iron on its heel or sliding the variable steam control fully to the left. min max CleanSelf ANTI-DRIP SYSTEM (depending on model) In order to produce steam, all irons require a high temperature. If the soleplate is not hot enough some of the water will not tur...