Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
• If you lower the thermostat, wait until the light goes out and comes on again before ironing. ! AUTO-STOP SAFETY FEATURE 3 (depending on the model) The electronic system cuts the power off and the auto-stop warning light (L) flashes if the iron is left vertically on its heel for more than 8 minutes or for more than 30 seconds if left horizontal. To restart the iron, shake it gently until the warning light stops flashing. NB. When the auto-stop safety switch operates, the thermostat light will remain off. ANTI-DRIP FUNCTION 4 Prevents drips whilst ironing. 8 Place the Steam control (G) on DRY . You can start ironing when the indicator light (I) comes on for the second time. IRONING WITHOUT STEAM TO IRON LINEN OR COTTON WITH A HIGH FLOW OF STEAM 7 1. Set the thermostat control to Linen or Cotton. 2. Press the “Jeans” (K) (depending on the model) trigger while ironing. This increases the flow of steam. 3. Do not press the trigger (depending on the model) for more than 30 seconds. Wait a minute before using it again. Press repeatedly on the Spray button to dampen the fabric. or Use the Burst of Steam button pressing two or three times in quick succession to obtain a more powerful burst of steam. Important Never use the Burst of Steam button on silk and synthetics. REMOVING THE STUBBORN CREASES 6 1. Hang the garment up and hold the fabric taut 2. Place the thermostat control (H) on MAX, press repeatedly on the Burst of Steam button and move the iron from top to bottom. Important Hold the iron a few centimetres from the garment to avoid burning delicate fabrics. VERTICAL STEAM ! 5 ! Self-cleaning (twice a month) 1. Fill the tank to the MAX mark (see our recommendations on the type of water to use). 2. Put the thermostat control (H) on MAX and the steam control (G) on and switch on. 3. Place the iron on its heel and wait around 5 minutes. 4. Unplug the iron and place over the sink horizontally. Push the lock (E) backwards to free the anti-calc valve, then remove it completely. 5. Shake the iron gently until most water (and any impurities) has drained from the soleplate. N.B. Once you have done this, it is normal for a little water to remain in the water tank because the iron’s anti-drip system may prevent the tank being completely emptied.This will not effect its ironing performance. 6. Replace the anti-calc valve (E). 7. When the soleplate is just warm, wipe the iron with a soft cloth. 8. To keep the anti-calc valve working, once a month leave it to soak in white vinegar or pure lemon juice for around 2 hours. Rinse the stem with water before inserting back in the iron. 9CARING FOR YOUR IRON ! Note! Your iron will only operate when the anti-calc valve is in place. 2 1 9CARING FOR YOUR IRON ! Note! Your iron will only operate when the anti-calc valve is in place. 2 1 ! CLEANING THE SOLEPLATE 10 Important Unplug your iron and let it cool down before cleaning. When the soleplate is cool, clean with a soft damp cloth or non-metallic washing up pad. Do not use detergent or descaling products. Never put the iron under the tap. We recommend that when using starch, it should be sprayed onto the reverse side of the fabric and the soleplate cleaned more frequently.Try to avoid ironing over zips which may have rough edges. 11PUTTING YOUR IRON AWAY 1. Set the steam control (G) on . 2. Unplug the iron. 3. Empty the tank over the sink. 4. Wind the cord loosely around the heel and fix the clip (J) onto the cord. 5. Store the iron upright on its heel. Never place it on a metallic support. Note Wait until the iron has cooled down before storing it. Never place it on a metallic support. ! This appliance is designed for domestic use only. In the case of professional use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee does not apply. SAFETY PRECAUTIONS 12 • Important! Your electrical installation must correspond to that of your iron (220240V). Connecting to the wrong voltage may cause irreparable damage to the iron and this will invalidate the guarantee. • This iron must be plugged into an earthed socket. If you are using an extension lead, ensure that it is bipolar (10A-or 13A for UK only) with an earth. • If the cord is damaged, it must be replaced immediately by an Approved Service Centre as this is dangerous. • Never immerse the iron in water! • The appliance must be unplugged before filling or emptying the tank • If the iron is dropped, have it checked by a professional before reuse: invisible damage may be dangerous. • Your appliance gives off steam which can cause burns. • The soleplate of the iron may be very hot: - never touch it - always leave it to cool before you put it away -never leave your iron unattended when plugged in or when the soleplate is still hot. - keep your iron away from children. Never take your iron apart: call the Helpline or consult your Approved Service Centre (see separate leaflet). Warning: this appliance must be earthed. ...