Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Before using your iron with the steam function for the first time, we recommend that you operate it in a horizontal position for a few moments, away from your linen, i.e. press several times on the Burst of Steam button . STEAM IRONING Turbo Pro Read these instructions carefully and make sure you keep them. HELPLINE : FOR ANY PROBLEMS OR QUERIES, PLEASE TELEPHONE 0845 602 1454 (UK - calls charged at local rate) or (01) 47 51947 (Ireland) 1 YOUR STEAM IRON Instructions for use B. Spray button D. Spray C. Water tank filler cover E. Anti-calc valve and lock F. Maximum tank filling point K. “Jeans” trigger (depending on the model) G. Dry / Steam control H. Thermostat control A. Burst of steam button J. Cord clip I. Thermostat light L. Auto stop safety warning light (depending on the model) Your iron is equipped with an integrated system that protects against the effects of lime-scale. Filling the tank 1. Place the steam control (G) on . 2. Open the cover of the water tank filler hole (C), place the iron on a table (not when iron is hot), as shown in the diagram, and then fill it. Important You should not fill the tank beyond the MAX level (iron standing vertically on the heel). The water to use in your iron Your iron has been designed to operate using tap water. However, if your water is very hard, mix it 50% tap water with 50% distilled water. Types of water to be avoided Do not add anything to the contents of the water tank, and do not use pure demineralised water, water from clothes dryers, scented or softened water, water from refrigerators, batteries or air conditioners, pure distilled water or rainwater. These contain organic waste or mineral elements that become concentrated when heated and cause spitting, brown staining or premature wear to your iron. Never use additives (perfumed water, starch, perfumed oils…) ! ! ! Important! (depending on the model). Take off the soleplate protection before heating the iron. 2. Place the Steam Control (G) on . The production of steam automatically adjusts to the temperature selected. 1. Place the thermostat control (H) to match the type of fabric to be ironed. The light comes on (I). Wait for the light to go off and come on again before you start ironing Our advice Start with the fabrics to be ironed on a low temperature (•) and finish with those which respond best to higher temperatures (••• or MAX) If you iron a fabric made of a blend of fibres: set the temperature for the most delicate fibre. 2SETTING THE TEMPERATURE AND THE STEAM LEVEL Linen Cotton Wool Silk (Viscose) Synthetics (Acetate, Acrylic, Polyamide, Polyester) Important • Your iron will only produce steam when the thermostat control is in the steam zone. When first switching on the iron wait for 5 minutes after the iron is switched on for steam to be produced. • If you lower the thermostat, wait until the light goes out and comes on again before ironing. ! 1. Place the thermostat control (H) to match the type of fabric to be ironed. The light comes on (I). Wait for the light to go off and come on again before you start ironing Our advice Start with the fabrics to be ironed on a low temperature (•) and finish with those which respond best to higher temperatures (••• or MAX) If you iron a fabric made of a blend of fibres: set the temperature for the most delicate fibre. 2SETTING THE TEMPERATURE AND THE STEAM LEVEL Linen Cotton Wool Silk (Viscose) Synthetics (Acetate, Acrylic, Polyamide, Polyester) Important • Your iron will only produce steam when the thermostat control is in the steam zone. When first switching on the iron wait for 5 minutes after the iron is switched on for steam to be produced. • If you lower the thermostat, wait until the light goes out and comes on again before ironing. ! AUTO-STOP SAFETY FEATURE 3 (depending on the model) The electronic system cuts the power off and the auto-stop warning light (L) flashes if the iron is left vertically on its heel for more than 8 minutes or for more than 30 seconds if left horizontal. To restart the iron, shake it gently until the warning light stops flashing. NB. When the auto-stop safety switch operates, the thermostat light will remain off. TO IRON LINEN OR COTTON WITH A HIGH 7 Press repeatedly on the Spray button to dampen the fabric. or Use the Burst of Steam button pressing two or three times in quick succession to obtain a more powerful burst of steam. Important Never use the Burst of Steam button on silk and synthetics. REMOVING THE STUBBORN CREASES 6 1. Hang the garment up and hold the fabric taut 2. Place the thermostat control (H) on MAX, press repeatedly on the Burst of Steam button and move the iron from top to bottom. Important Hold the iron a few centimetres from the garment to avoid burning delicate fabrics. VERTICAL STEAM ! 5 ! ANTI-DRIP FUNCTION 4 The supply of water is cut off automatically to avoid any drips from the soleplate when the temperature of the iron is too low to produce steam. IRONING WITHOUT STEAM FLOW OF STEAM (depend...