Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
• The thermostat light comes on (fig.4). It will go out when the soleplate is hot enough. • Set the steam control (fig.5) to the desired position, consulting the table below. FABRIC THERMOSTAT DIAL POSITION STEAM SETTING POSITION LINEN MAX COTTON ••• WOOL •• SILK SYNTHETIC (Polyester, Acetate, Acrylic, Nylon) • = STEAM ZONE • Your iron heats up quickly: so begin by ironing fabrics that are ironed at low temperatures first, then go on to those requiring a higher temperature. . Spray Function • Whether steam or dry ironing, you are able to use the Spray button (fig.6) to dampen laundry to remove stubborn creases. Store your iron • Set the steam control to and unplug the iron. • Wait until the soleplate cools down and empty the tank. A little water may remain in the tank. • Wind the cord around the heel of the iron. • Store the cold iron on its heel (fig.7). Maintenance and cleaning Cleaning the anti-calc valve (once a month) • Unplug your iron and empty the water tank. • Remove the anti-calc valve (fig.8). • Soak the valve in a cup of white vinegar or plain lemon juice for 4 hours. (fig.9). • Rinse the valve under running water and replace the anti-calc valve. Unplug your iron and let it cool down before cleaning it. The iron will not function without the anti-calc valve. Never touch the end of the valve ! To slow down scaling and prolong the useful life of your iron, carry out the self-cleaning operation once a month. Carry out the self-cleaning operation (once a month) • Unplug your iron, set the steam control to and fill the water reservoir to MAX. • Place your iron on its heel, set the thermostat button to MAX, plug in your iron and wait for the indicator light to go out. • Unplug the iron and place it horizontally over a sink. • Remove the anticalc valve (fig.8). • Gently shake the iron over the sink until some of the water (along with impurities) runs out through the soleplate. • At the end of the operation, put the anticalc valve back in place and then plug in your iron for 2 minutes on its heel to dry the soleplate. Cleaning the soleplate • Unplug the iron, and when the soleplate is just warm, wipe it with a soft Never use abrasive or aggressive products. cloth. If there is a problem GB PROBLEM POSSIBLE CAUSE SOLUTION Water drips from the holes in the soleplate. The chosen temperature is too low and does not allow for the formation of steam. Position the thermostat in the steam range (from •• to MAX). You are using steam while the iron is not hot enough. Wait until the thermostat light goes out. There is too much steam. Reduce the steam. You have stored the iron horizontally, without emptying it and without setting it to . See the section "Store your iron". Brown streaks come through the holes in the soleplate and stain the linen. You are using chemical descaling agents. Do not add any descaling agents to the water in the water tank. You are not using the right type of water. Perform a self-cleaning operation and consult the chapter "What water to use ?". Fabric fibres have accumulated in the holes of the soleplate and are burning. Perform the self-cleaning operation and clean the soleplate with a damp sponge. Vacuum the holes of the soleplate from time to time. Your linen has not been rinsed sufficiently or you have ironed a new garment before washing it. Make sure that your laundry is rinsed sufficiently so as to remove any deposits of soap or chemical products on new clothes. The soleplate is dirty or brown and can stain the linen. You are ironing with an inappropriate setting (temperature too high). Clean the soleplate as indicated above. Select the appropriate program. You are using starch. Clean the soleplate as indicated above. Always spray starch onto the reverse side of the fabric to be ironed. There is little or no steam. The water tank is empty. Fill it. The anti-calc valve is dirty. Clean the anti-calc valve. Your iron has a build-up of scale. Clean the anti-calc valve and carry out a self-clean. Your iron has been used dry for too long. Carry out a self-clean. The soleplate is scratched or damaged. You have placed your iron flat on a metallic rest-plate or ironed over a zip. Always set your iron on its heel. Steam or water come from the iron as you finish filling the tank. The steam control is not set to the position. Check that the steam control is set to the position. The spray does not spray. The water tank is not full enough. Fill up the water tank. If you have any problem or queries, please contact an Approved Service Center. Environment protection first ! Your appliance contains valuable materials which can be recovered or recycled. Leave it at a civic waste disposal centre. SSEAC TEFAL 1460-1740SSEAC TEFAL 1265127or Description 1. Spray 7. Voyant et repere reglage du thermostat 2. Tige anti-calcaire 8. Talon Extra Stable* (selon modele) 3. Commande vapeur 9. Bouton du thermostat 4. Orifice de remplissage 10. Repere maxi du reservoir 5. Touche Spray 11. Semelle 6. Cordon d’alimentat...