Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Do not leave iron unattended while connected or on an board. Always position iron carefully to prevent it from falling board is accidentally moved or cord is pulled. Always use heel . Burns can occur from touching hot metal parts, hot water, caution when you turn a steam iron upside down or use steam — there may be hot water in the water tank. movement of iron to minimize hot water spillage. SPECIAL INSTRUCTIONS . To avoid a circuit overload, do not operate appliance on the same circuit. . If an extension cord is absolutely necessary, or 6-ampere and 220-volt cord should amperage may overheat. Care it cannot be pulled or tripped SAVE THESE 7 Soft-Touch Parts Note: The soft-touch parts of this unit are free of natural rubber and latex. They are safe for individuals allergic or sensitive to these materials. POLARIZED PLUG (120V Models Only) This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way. TAMPER-RESISTANT SCREW Warning : This appliance is equipped with a tamper-resistant screw to prevent removal of the outer cover. To reduce the risk of fire or electric shock, do not attempt to remove the outer cover. There are no user-serviceable parts inside. Repair should be done only by authorized service personnel Note: If the power supply cord is damaged, it should be replaced by qualified personnel or in Latin America by an authorized service center. 8 AS385Pub10000001628R2 2/2/06 3:14 PM Page 10 Product may vary slightly from what is illustrated. 1. Spray nozzle 2. Water-fill cover 3. Dry/Steam selector 4. Spray button 5. Surge-of-steam button 6. Handle 7. Pivoting cord 8. Fabric guide 9. Heel rest 10. Temperature-ready indicator light 11. Fabric-select dial 12. Water tank 13. Soleplate 9 Dry Steam/Blast of Steam Spray Symbols How to Use This appliance is for household use only. GETTING STARTED Remove any labels, stickers or tags attached to the body or soleplate of the iron. Note: Use ordinary tap water for ironing. Do not use water processed through a home softening system. Important: For optimum performance, let the iron stand for 90 seconds before beginning to iron. TO FILL THE WATER TANK A B C D 1. Grasp the water-fill cover and pull it out to expose the water-fill hole. Be careful not to pull too hard as the water-fill cover is attached to the inside of the water-fill hole (A) . 2. Tilt the iron and using a clean measuring cup, pour water into opening until the water reaches the MAX level mark on the water tank (B) . Do not overfill. 3. After filling, be sure to push the water-fill cover securely back into the water-fill hole. 4. Plug in the iron. The power on indicator light comes on (C) . Tip: If unsure of a garment’s fiber, test a small area (on an inside seam or hem) before ironing. FOR STEAM IRONING 1. Turn the selector to the desired steam level. To get maximum steam, set the selector to the middle position (D) . Steam is produced as soon as you hold the iron. Important: Do not set the selector past the middle position. 2. Turn the fabric-select dial to appropriate setting (between 4 and 6) for your fabric (E) . See fabric guide on the heel rest and read garment’s label to help you fabric type. E • The temperature-ready light glows until appropriate temperature. • It then glows on and off during ironing. 3. When finished ironing, turn the the selector to and unplug the iron. FOR DRY IRONING 1. Make sure selector is set . You may wan...
Эта инструкция также подходит к моделям:Утюги - AVANTSTEAM AS390 (972.24 kb)
Утюги - AVANTSTEAM AS395 (972.24 kb)